Förster-Technik TAP5-VS2-50 Скачать руководство пользователя страница 58

Страница: 58 / 130

Programming and control

4.3.

If there is a version available for the

peripheral devices

, the message

Peripherals

update available...

will appear

Press <Enter> to download and install the new

firmware!

. Confirm with

, to start the download.

4.4.

Once the download has been completed, the message

Download completed

will

appear.

Press <Enter> to start installation

. Confirm with

, to start the update.

4.7.3

Software update via internal (automatic)

The expert menu

Device data > Software Update > Internal (automatic)

is intended for use

by the manufacturer. By this means a software update can be performed via a micro SD card in
the control box of the automatic feeder and the FTP Manager.

4.8

Reinstallation

In the event of a fault in the course of reinstallation, delete all the data saved on the automatic
feeder.

All the device data, plans and medicine formulations will be reset to factory settings and all an-
imal data and transmitters deleted.

Perform a reinstallation as follows:

1. Switch the automatic feeder off.

2. Press

and keep the key depressed whilst you switch the automatic feeder on and

wait until the message

Reinstallation

appears in the display.

3. Confirm with

, to continue. The automatic feeder will restart and all the data will be de-

leted.

4. Set the desired

language

and confirm it with

5. Set the current

date

and confirm it with

6. Set the current

time

and confirm it with

The automatic feeder will switch to the

Setup menu

7. Read the

ID chip

8. Check the setup settings as follows:

All the device data, plans and medicine formulations were reset to factory settings and all
animal data and transmitters were deleted.

9. Perform a data restoration (see 4.6.7 "Backing up and restoring data" - 52) and set up the

automatic feeder.

Содержание TAP5-VS2-50



































































































































Результаты поиска

Содержание TAP5-VS2-50

Отзывы:

Похожие инструкции для TAP5-VS2-50

Бренды по названию

Популярные бренды

Förster-Technik TAP5-VS2-50, Оригинальное сервисное руководство

Результаты поиска

Содержание TAP5-VS2-50

Отзывы:

Похожие инструкции для TAP5-VS2-50

Бренды по названию

Популярные бренды