Förster-Technik TAP5-VS2-50 Скачать руководство пользователя страница 46

Страница: 46 / 130

Programming and control

Note:

These settings are used during the preparation of all feed portions.

4.6.2

Checking and setting time/date

During commissioning, you have to check and, if necessary, correct the time and the date.

Set the time of day, date and date format as follows:

1. Navigate via

> Device data

to the

Time/date

sub-menu.

2. In

Time

, you enter the current time of day.

3. In

Date

, you enter the current date.

Note:

In order to force an immediate daily offset after changing the date, you have to switch the

feeder off and then on again.

4.6.3

Setting portion

The automatic feeder and preparation of the feed are designed so that even a milk substitute
with a higher fat melting point can be easily processed.

NOTICE!

Feed temperatures that are too low can cause digestion problems in calves and feed tem-
peratures that are too high can cause gastritis in the abomasum.

The temperature of the feed in the mixer beaker must correspond to the mixing temperature
specified by the MP manufacturer.

►

Keep to the feed temperatures recommended in this operating manual.

In this menu, you make the following settings for the feed portion:

•

They set the set temperature of the feed in the mixer beaker.

•

They set the minimum temperature of the water in the boiler.

•

They set a pause between the dispensing of two portions.

•

In conjunction with the IFS feeding station (optional) they set a portion amount <250 ml and
the tolerance values for the concentration.

•

They set the parameters for the procedure for discharging the mixer and for the overrun.

4.6.3.1

Setting the set temperature and minimum temperature

Note:

The first portion of feed, depending on the ambient temperature, is always mixed some-

what warmer.

This is how you set the set temperature and the minimum temperature:

1. Navigate via

> Device data

to the

Portion

sub-menu.

2. Enter the desired set temperature in

Set temp.

of the feed in the mixer beaker (= mixing

temperature).

3. In the

Min. Temp.

, enter the desired minimum temperature of the water in the boiler.

Содержание TAP5-VS2-50



































































































































Результаты поиска

Содержание TAP5-VS2-50

Отзывы:

Похожие инструкции для TAP5-VS2-50

Бренды по названию

Популярные бренды

Förster-Technik TAP5-VS2-50, Оригинальное сервисное руководство

Результаты поиска

Содержание TAP5-VS2-50

Отзывы:

Похожие инструкции для TAP5-VS2-50

Бренды по названию

Популярные бренды