Förster-Technik TAP5-VS2-50 Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 130

background image

Faults and warnings

109

9.5.1.2

Motors

Check the motors as follows:

1. Navigate via

> Diagnostics

to switch to the

Motors

sub-menu.

2. Confirm

Mixer: start?

by choosing

, to start the mixer.

3. Confirm

Powder start?

by choosing

, to start the powder conveyor.

4. In the

flushing agent 1

menu, press

.

4.1.

Confirm

check?

by choosing

, to check the cleaning agent pump.

4.2.

Confirm

Flushing agent: start?

by choosing

, to start the cleaning agent pump.

Check that cleaning agent flows from the outlet.

5. In the

start flushing agent 2?

menu, press

.

5.1.

Confirm

check?

by choosing

, to check the cleaning agent pump.

5.2.

Confirm

Flushing agent: start?

by choosing

, to start the cleaning agent pump.

Check that cleaning agent flows from the outlet.

WARNING!

Hazardous or irritant materials!

►

Collect the cleaning agent residues and additive residues and dispose of them safely. When
doing this be sure to comply with the manufacturer's instructions and national regulations for
the use and disposal of the cleaning agent and additive being used. In addition a mixer
cleaning must then be performed.

6. Confirm

Feeding pump: start?

by choosing

, to start the feeding pump.

9.5.2

Checking the heating

In this menu, you check the boiler heating system.

Check the boiler heating system as follows:

1. Navigate via

> Diagnostics

to switch to the

Heating system

sub-menu.

2. Confirm

switch on?

by choosing

.

3. In the

Boiler

menu, you check the temperature.

4. Keep the

in

switch on?

Depressed, the boiler will then heat up. If the temperature rises,

that means the heater is working.

«
...
107
108
109
110
111
...
»

Содержание TAP5-VS2-50



































































































































Отзывы:

Нет отзывов

Похожие инструкции для TAP5-VS2-50

Бренд: baliv Страницы: 36

Бренд: Moen Страницы: 1

Alessandra Ambrosio AHC 34

Бренд: Beurer Страницы: 72

Lustertone ELU1317

Бренд: Elkay Страницы: 1

Бренд: Grohe Страницы: 32

Бренд: Hans Grohe Страницы: 40

Бренд: Columbia Products Страницы: 3

HydroTap G5 Classic Plus

Бренд: Zip Страницы: 44

Бренд: UBERHAUS DESIGN Страницы: 3

Бренд: Kohler Страницы: 24

Бренд: Viega Страницы: 70

230 Showerarm 26435 1 Series

Бренд: Axor Страницы: 24

Бренд: Beagle Страницы: 2

Бренд: Creavit Страницы: 18

Бренд: American Standard Страницы: 6

Town Square Two-Piece Toilets 2787

Бренд: American Standard Страницы: 4

Aluminum Framed Fabric Restbenches

Бренд: Mason Страницы: 4

Aluminum Framed Panel Mount Swing Up Rest Benches

Бренд: Mason Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды