manualshive.com logo in svg

Fluke PG9000 Series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Fluke PG9000 Series Скачать руководство пользователя страница 93

 

3. GENERAL OPERATION 

 

Page 83 

 

© 2011 Fluke Calibration 

  OPERATION 

To select a SETUP file number to make it the active SETUP file, press 

[SETUP]

 and select 

<1select>

.  In the following screen enter the number of the desired SETUP file and press 

[ENT]

.  If a valid SETUP file number has been entered, operation returns to the previous run 

screen with the selected SETUP file number displayed and active. 

Note 

•

 

Entering an invalid SETUP file number causes an error message to be 
displayed briefly and returns to the select SETUP file screen. 

•

 

If the SETUP file selected specifies COM2 as the source of barometric 
pressure,  PG9000  will attempt to read a barometer on COM2 when 
initializing the new SETUP file.  If PG9000 is unable to read a barometer on 
COM2, a communications time out message is displayed briefly and 
operation returns to the select SETUP file screen.  See Section 3.12.5.4 for 
information on configuring COM2 to read an external barometer. 

3.11.2  <2view>  

  PURPOSE 

To view the variable source choices and values of any SETUP file number. 

  OPERATION 

Note 

•

 

Selecting <2view> SETUP allows the variable source choices and values of 
the active SETUP file for viewing only.  <2view> does not make the viewed 
SETUP file active.  To select the active SETUP file, press [SETUP] and 
select <1select>. 

•

 

See Table 16 for a listing of the source choices for each variable. 

To view an existing SETUP file, press 

[SETUP]

 and select 

<2view>

.  The display is: 

1. 

Entry field for number of SETUP file to be  viewed.  Defaults 
to SETUP file currently selected.  Must be a number from 2 to 
10. 

View SETUP file: 

#02 

   

 

 

Enter the desired SETUP file number and press 

[ENT]

.   

 

<1atmP>

  to view the atmospheric pressure variable source choice and current value.  The 

value is displayed in the current pressure units (see Section 3.10.3). 

<2ambT>

  to view the ambient temperature variable source choice and the current value.  

The value is displayed in degrees Centigrade (

°

C). 

<3%RH>

 to view the ambient relative humidity variable source choice and the current value.  

The value is displayed in “%RH”. 

<4PCT>

 to view the piston-cylinder temperature variable source choice and the current value.  

The value is displayed in degrees Centigrade (

°

C). 

<5g>

 to view the gravity variable source choice and the current value.  The value is displayed 

in meters per second squared (m/s

2

). 

If a valid SETUP file number is entered, the display is: 

View #02 latmP 2ambT 

3%RH 4PCT 5g 6READY

 

 7vac 

 

Содержание PG9000 Series











































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды