Fluke PG9000 Series Скачать руководство пользователя страница 169

Страница: 169 / 202

5. MAINTENANCE, ADJUSTMENTS AND CALIBRATION

Page 159

The values of resistances at 0

C and the slopes, if desired, can be edited to

reflect the new calibration by pressing

[SPECIAL], [7cal]

and selecting

<4PCT1>

for the first PRT, or

<5PCT2>

for the second PRT.



OPERATION

To view the output of the piston-cylinder module temperature sensors, press

[SPECIAL], <7cal>, <4PCT1>

<1view>

[SPECIAL], <7cal>, <4PCT2>

<1view>.

The display is:

Current reading of the selected piston-
cylinder module temperature sensor in
degrees Centigrade.

Indication that this is a piston-cylinder
module temperature display, and which
sensor.

Current value of the resistance slope relative
to temperature.

Current value of the offset at 0 °C in ohm.

19.951 °C PCT1

RZ100.003

Ω S0.389

To adjust the values of

and/or

, press

[SPECIAL] , <7cal>

and select either

<4PCT1>

<2cal>

<4PCT2>

<2cal>

to access a screen in which the values of

and

can be edited. From here, press

[ESC]

and select

<1view>

to view the

individual PRT reading with the edited calibration coefficients applied.

To remove the mounting post PRTs:

Mounting Post PRT Removal



Remove the piston-cylinder module from the mounting post and replace with

the ORANGE storage plug.



Disconnect the PG9000 Platform from the PG9000 Terminal.



Turn upside down the PG9000 Platform so that the bottom of the platform is

up. Support the platform so that it does not tip over. A simple solution is to
place the platform upside down on a sturdy box which is smaller than the
outside platform dimensions and is also tall enough to allow the mounting
post to be suspended.



Remove the two socket head screws (2.5 mm Allen tool), securing the small

circular AMH DRIVE connector bulkhead plate to the platform rear panel.



PRT1



PRT2



Socket Head Screws

Figure 22.

PG9602 bottom panel detail.

Содержание PG9000 Series











































































































































































































Результаты поиска

Содержание PG9000 Series

Отзывы:

Бренды по названию

Популярные бренды

Fluke PG9000 Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание PG9000 Series

Отзывы:

Бренды по названию

Популярные бренды