Fluke PG9000 Series Скачать руководство пользователя страница 58

Страница: 58 / 202

PG9602™ OPERATION AND MAINTENANCE MANUAL

Page

AMH

ERROR

NUMBER

PG TERMINAL MESSAGE

COMMENT

None

Missing or improper argument.

None

Unknown Command.

None

Invalid command suffix.

None

Receive buffer overflow. Buffer has been flushed.

None

Command not available.

None

Watchdog reset has occurred.

100

None

Present mass setting unknown.

102

None

6.2 kg binary mass not available on AMH.

103

<AMH memory failure>

Mass memory.

104

<AMH memory failure>

Non-volatile memory is corrupt.

105

<AMH logic failure>

Fatal electronics error.

106

None

Mass load must first be lifted.

107

<AMH logic failure>

Incorrect CPLD version.

108

<AMH logic failure>

CPLD logic error.

110

Column motor switch error on column 0 (C0).

111

Column motor switch error on column 1 (C1).

112

Column motor switch error on column 2 (C2).

113

Wrong column switch detected.

114

<AMH logic failure>

JTAG buffer overflow.

115

<AMH logic failure>

JTAG max retries.

116

<AMH logic failure>

JTAG TDO mismatch.

117

<AMH logic failure>

JTAG illegal state.

118

<AMH logic failure>

JTAG ENDxR state unknown.

119

<AMH logic failure>

JTAG unknown error.

120

<AMH unable to lift mass load>

Mass lift valve not sensed.

121

<AMH unable to lower mass load>

Mass is dropping unexpectedly.

122

<AMH unable to lift mass load>

Mass never lifted.

123

<AMH unable to lower mass load>

Mass is not dropping when it should.

124

<AMH unable to lift mass load>

IR beam malfunction. AMH will not attempt lift

125

Column motor switch on column 1 is misaligned.

126

Column motor switch on column 2 is misaligned.

130

<AMH valve failure>

6.4 kg binary mass pin engage valve (VLV#14) not sensed.

131

<AMH valve failure>

3.2 kg binary mass pin engage valve (VLV#6) not sensed.

132

<AMH valve failure>

1.6 kg binary mass pin engage valve (VLV#12) not sensed.

133

<AMH valve failure>

0.8 kg binary mass pin engage valve (VLV#4) not sensed.

134

<AMH valve failure>

0.4 kg binary mass pin engage valve (VLV#10) not sensed.

135

<AMH valve failure>

0.2 kg binary mass pin engage valve (VLV#2) not sensed.

136

<AMH valve failure>

0.1 kg binary mass pin engage valve (VLV#8) not sensed.

137

<AMH valve failure>

6.4 kg binary mass pin disengage valve (VLV#15) not
sensed.

138

<AMH valve failure>

3.2 kg binary mass pin disengage valve (VLV#7) not sensed.

Содержание PG9000 Series











































































































































































































Результаты поиска

Содержание PG9000 Series

Отзывы:

Бренды по названию

Популярные бренды

Fluke PG9000 Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание PG9000 Series

Отзывы:

Бренды по названию

Популярные бренды