manualshive.com logo in svg

Fluke OC3port Plus, Руководство пользователя

Поделиться
Скачать
Fluke OC3port Plus Скачать руководство пользователя страница 215

OC3port Plus

User Manual

6-84

15.

 

Press the 

Down Arrow

 key to move the 

Setup XMIT Streams

 option to the

selection line. Press 

ENTER

. The setup menu for 

TRANSMIT STREAM 1

 is

displayed:

 TRANSMIT STREAM:        1

           

  

    or    for Change                         
 NAME:XMITHDR_1 
 SOURCE   OFF 

za167f.eps

 

Note

 

The IP Ping test is conducted on TRANSMIT STREAM 1. Therefore,
make sure that you display the setup menu for this transmission
stream.

 

16. Program TRANSMIT STREAM 1 with the desired header information.

 

Note

 

The OC3port Plus uses the VPI / VCI specified for TRANSMIT
STREAM 1 to transmit IP Ping messages and to monitor responses
to those messages. Therefore, for the OC3port Plus to detect a
response from the device under test, that response must be sent back
to the tester on the same VPI / VCI.

 

17. Press the 

ATM

 key again. You return to the 

ATM SELECTIONS

 menu.

18.

 

Press the 

Down Arrow

 key to move the 

ATM XMIT Mode

 option to the selection

line:

  ATM SELECTIONS:
  Load XMIT Streams
  ATM XMIT Mode             STR
  Cell Capture
  

za168f.eps

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание OC3port Plus

























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды