manualshive.com logo in svg

Fluke OC3port Plus, Руководство пользователя

Поделиться
Скачать
Fluke OC3port Plus Скачать руководство пользователя страница 201

OC3port Plus

User Manual

6-70

2-point CDV Test

 

A 2-point CDV test is concerned with cell delivery times, specifically with the
actual delay experienced by cells transmitted between two points in a network.
During this test, the OC3port Plus captures a sample of cells and calculates the cell
transfer delay. The tester reports the delay in cell times.

Setting Up a 2-point CDV Test

 

Note

 

The OC3port Plus, at best, can guarantee a CDV of two cell times
for each transmission stream. Therefore, a minimum CDV test result
that uses the OC3port Plus as a source will be 2.0 cell times.

 

The same OC3port Plus analyzer must be used in this test as both the
source and receiver of test traffic because the transmit and receive
time stamps must originate from the same timing source.

 

The operation of this test depends on the transmit stream definitions
selected when the test is run. If, for example, TRANSMIT STREAM 3
is used to perform the test, only cells that have headers matching this
stream are analyzed.

 

To set up the OC3port Plus to perform a 2-point CDV test, complete these steps:

 

1. Press the 

ATM

 key. The 

ATM SELECTIONS

 menu is displayed.

2.

 

Press the 

Down Arrow

 key to move the 

Setup XMIT Streams

 option to the

selection line. Then, press 

ENTER

. One of the 

TRANSMIT STREAM

 setup menus

is displayed. For example:

 TRANSMIT STREAM:        1

   

    or    for Change            
 NAME:XMITHDR_1 
 SOURCE   CBR 

za063f.eps

 

3. Press the 

Left

 or 

Right Arrow

 key to display the transmission stream that you

want to configure.

 

4. Press the 

Down Arrow

 key to move the header and traffic parameters that you

want to program to the selection line. Then, supply the desired values.

 

Note

 

Make sure that the 

PAYLOAD

 parameter is set to 

FIXED

.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание OC3port Plus

























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды