Fluke MDA-510 Скачать руководство пользователя страница 9

Страница: 9 / 36

Motor Drive Analyzer

Safe Use of Li-ion Battery Pack

Recommendations for safe use of the battery
pack:
•

The battery pack must be charged before
use. Use only Fluke approved power

adapters to charge the battery pack. Refer
to Users Manual for proper charging
instructions.

•

Do not leave a battery on prolonged charge
when not in use.

•

The battery pack gives the best
performance when operated at normal
room temperature 20

C (68

F).

•

Do not put battery packs near heat or fire.
Do not put in sunlight.

•

Do not subject battery packs to severe
impacts such as mechanical shock.

•

Keep the battery pack clean and dry. Clean
dirty connectors with a dry, clean cloth

•

Do not use any charger other than that
specifically provided for use with this
equipment.

•

Do not use any battery which is not
designed or recommended by Fluke for use
with the

Product.

•

Take careful notice of correct placement of
the battery in the product or the External

Battery Charger.

•

Do not short-circuit a battery pack. Do not
keep battery packs in a place where the

terminals can be shorted by metal objects
(e.g. coins, paper clips, pens or other).

•

Never use a battery pack or charger
showing visible damage.

•

Batteries contain hazardous chemicals that
can cause burns or explode. If exposure to

chemicals occurs, clean with water en get
medical aid. Repair the Product before use
if the battery leaks.

•

Alteration of battery pack: there shall be no
attempt to open, modify, reform or repair a
battery pack, which appears to be
malfunctioning, or which has been
physically damaged.

•

Do not disassemble or crush battery packs

•

Use the battery only in the application for
which it is intended.

•

Retain the original Product information for
future reference.

Содержание MDA-510





































Результаты поиска

Содержание MDA-510

Отзывы:

Бренды по названию

Популярные бренды

Fluke MDA-510, Руководство пользователя

Результаты поиска

Содержание MDA-510

Отзывы:

Бренды по названию

Популярные бренды