Fluke MDA-510 Скачать руководство пользователя страница 6

Страница: 6 / 36

MDA-550/MDA-510

Users Manual

The accessory set that is included for the Motor Drive
Analyzer is different than the ScopeMeter

Test Tool 190

Series II. See

In The Box

in this manual.

For User Manual corrections, download the latest manual
supplement at

http://us.fluke.com/usen/support/manuals

How to Contact Fluke

To contact Fluke, use one of these telephone numbers:
•

USA: 1-800-760-4523

•

Canada: 1-800-36-FLUKE (1-800-363-5853)

•

Europe: +31 402-675-200

•

Japan: +81-3-6714-3114

•

Singapore: +65-6799-5566

•

China: +86-400-921-0835

•

Brazil: +55-11-3530-8901

•

Anywhere in the world: +1-425-446-5500

Or, visit Fluke's website at

www.fluke.com

To register your Product, visit

http://register.fluke.com

To view, print, or download the latest manual supplement,
visit

http://us.fluke.com/usen/support/manuals

Safety Information

Warning

identifies hazardous conditions and procedures

that are dangerous to the user. A

Caution

identifies

conditions and procedures that can cause damage to the
Product or the equipment under test.

Warning

To prevent possible electrical shock, fire, or
personal injury:
•

Read all safety information before you use
the Product.

•

Carefully read all instructions.

•

Do not alter the Product and use only as
specified, or the protection supplied by the
Product can be compromised.

•

Use only the Fluke power supply, model
BC190 (Power Adapter).

•

Before use, check that the
selected/indicated range on the BC190
matches the local line power voltage and
frequency.

•

For the BC190 Power Adapter only use line
cords that comply with the local safety
regulations.

•

Use only insulated voltage probes, test
leads, and adapters supplied with the
product, or indicated by Fluke as suitable
for the MDA-550/MDA-510 Motor Drive
Analyzer or Fluke 190 II ScopeMeter series.

Содержание MDA-510





































Результаты поиска

Содержание MDA-510

Отзывы:

Бренды по названию

Популярные бренды

Fluke MDA-510, Руководство пользователя

Результаты поиска

Содержание MDA-510

Отзывы:

Бренды по названию

Популярные бренды