manualshive.com logo in svg

Fluke MDA-510, Руководство пользователя

Поделиться
Скачать
Fluke MDA-510 Скачать руководство пользователя страница 36

MDA-550/MDA-510

Users Manual

32

Electromagnetic Compatibility (EMC)

International ..............................................................IEC 61326-1: Portable Electromagnetic Environment IEC 61326-2-2

CISPR 11: Group 1, Class A
Group 1: Equipment has intentionally generated and/or uses conductively-coupled radio frequency 

energy that is necessary for the internal function of the equipment itself.
Class A: Equipment is suitable for use in all establishments other than domestic and those directly 

connected to a low-voltage power supply network that supplies buildings used for domestic purposes. 

There may be potential difficulties in ensuring electromagnetic compatibility in other environments due 

to conducted and radiated disturbances. 
Caution: This equipment is not intended for use in residential environments and may not provide 

adequate protection to radio reception in such environments.
Emissions that exceed the levels required by CISPR 11 can occur when the equipment is connected to 

a test object.

Korea (KCC) .............................................................Class A Equipment (Industrial Broadcasting & Communication Equipment)

Class A: Equipment meets requirements for industrial electromagnetic wave equipment and the seller 

or user should take notice of it. This equipment is intended for use in business environments and not to 

be used in homes.

USA (FCC)................................................................47 CFR 15 subpart B. This product is considered an exempt device per clause 15.103.

Note

For EMC immunity, see Section 8, Table 3 in the ScopeMeter Test Tool 190 Series II Users Manual.

Содержание MDA-510





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды