manualshive.com logo in svg

Fluke MDA-510, Руководство пользователя

Поделиться
Скачать
Fluke MDA-510 Скачать руководство пользователя страница 12

MDA-550/MDA-510

Users Manual

8

In The Box

The test tool includes:
•

MDA-550 or MDA-510 Motor Drive Analyzer 

•

3 VPS 100:1 high voltage probe sets and alligator clips

•

1 VPS410 10:1 high frequency probe set

•

Extension ground lead, 1 meter (only recommended to 
connect to ground when using the ground lead that is 
included with the VPS is not practical)

•

i400s current clamp for MDA-510, 3 i400s current 
clamps for MDA-550

•

Battery Pack BP291 - 52 Wh (to be installed in the unit)

•

Hang Strap

•

BC190 Power Adapter

•

Regional Power Cords

•

Safety Information (Multi-Language)

•

USB drive (with multi-language User Manuals and 
FlukeView ScopeMeter PC Software)

•

USB Interface Cable for PC Connection (USB A-to-mini 
USB B)

•

Soft Carry Case C1740

The MDA-550 includes a Shaft Voltage Test Set to make 
the connection with a rotating shaft:
•

set of 3 brushes

•

probe holder

•

two-piece extension rod

•

magnetic base

Input Connections

The top of the test tool has four safety BNC signal inputs. 
These isolated inputs allow independent floating 
measurements with each input. See Figure 1.

Figure 1. BNC Connectors

To make motor drive voltage and current measurements:
1. Connect the voltage probe to input A.
2. Connect the voltage probe tip to a phase. 
3. For Phase-Phase measurements, connect the ground 

lead to another phase that is used as a reference. 

4. For Phase-Ground measurements, connect the ground 

lead to ground. 

5. For the current measurement, place the clamp around 

one phase and connect the current probe to input B. 
After measurement selection, an on-screen connection 
diagram shows the connections for each measurement.

ALL INPUTS ISOLATED

!

Содержание MDA-510





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды