manualshive.com logo in svg

Fluke MDA-510, Руководство пользователя

Поделиться
Скачать
Fluke MDA-510 Скачать руководство пользователя страница 8

MDA-550/MDA-510

Users Manual

4

•

Examine the case before you use the 
product. Look for cracks or missing plastic. 
Carefully look at the insulation around the 
terminals.

•

Do not work alone.

•

Comply with local and national safety 
codes. Use personal protective equipment 
(approved rubber gloves, face protection, 
and flame resistant clothes) to prevent 
shock and arc blast injury where hazardous 
live conductors are exposed.

•

The battery door must be closed and 
locked before you operate the product.

•

Do not operate the Product with covers 
removed or the case open. Hazardous 
voltage exposure is possible.

•

Remove the input signals before you clean 
the Product.

•

Use only specified replacement parts.

•

Do not use test leads if they are damaged. 
Examine the test leads for damaged 
insulation, exposed metal, or if the wear 
indicator shows. Check test lead 
continuity.

Safe Use of Li-ion Battery Pack

The battery pack Fluke model BP291 (52 Wh) has been 
tested in accordance with the UN Manual of Tests and 
Criteria Part III Subsection 38.3 (ST/SG/AC.10/11/Rev.3) – 
more commonly known as the UN 38.3 – tests, and have 
been found to comply with the stated criteria. The battery 
pack has additionally been tested according to IEC 62133.

Recommendations for safe storage of 
battery pack:
•

Do not store battery packs near heat or fire. 
Do not store in sunlight.

•

Do not remove a battery pack from its 
original packaging until required for use.

•

When possible, remove the battery pack 
from the equipment when not in use.

•

Fully charge the battery pack before 
storing it for an extended period to avoid a 
defect.

•

After extended periods of storage, it may 
be necessary to charge and discharge the 

battery packs several times to obtain 
maximum performance.

•

Keep the battery pack out of the reach of 
children and animals.

•

Seek medical advise if a battery or part of it 
has been swallowed.

Содержание MDA-510





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды