manualshive.com logo in svg

Fluke MDA-510, Руководство пользователя

Поделиться
Скачать
Fluke MDA-510 Скачать руководство пользователя страница 17

Motor Drive Analyzer

Navigation and User Interface

13

Keys

This section is an overview of the keypad functions:

In the main menu the button bar shows the options for the 
function keys:

Close Report

A report is a selection of screen bitmaps files. When you 
save a measurement, use 

Save Report

 to save a screen 

bitmap. When all the measurements are done, use 

Close

 

Report in the main menu to close the report. You must close 
the report before you can start a new report. The report also 
closes automatically when you turn off the Product.

Copy Report to USB

After a report is closed, you can save the report to a USB 
drive (max 2 GB). 

Delete Report

Delete a saved report.

Info

Use the Info screen to find explanations about the 
selections and corresponding measurements, including tips 
and tricks.

Probes

Select the probes to specify the type of voltage and current 
probes. Make sure the clamp and the measurement 
instrument are set to the proper range. Use the range select 
switch on the clamp to adapt the setting if necessary. The 
arrow on the top of the clamp must face towards the load of 
the circuit. Connect the current clamp jaws around the 
conductor to be measured.

Manually changes the view of the 
waveform. Select the Input Channel 
with these keys. The D channel is not 
used in the Motor Drive Analyzer mode.

Change the view of the waveform on 
the selected Input Channel.

Changes the time base.

Turn off a channel. Use the same key 
again to return to the screen with the 
motor drive button bar.

This key is disabled as special settings 
apply for motor drive signals.

Use these keys the same as in Scope 
mode. Use the same key again to 
return to the screen with the motor drive 
button bar.

Freezes the screen (all readings and 
waveforms) at any time.

Removes the button bar from the 
screen. This is useful when the button 
bar overlaps part of the waveform.

MOVE

 

mV

V

RANGE

TIME

s

ns

ZOOM

REPLAY

 

TRIGGER

CURSOR

 

HOLD

RUN

 

CLEAR

Содержание MDA-510





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды