manualshive.com logo in svg

Fluke MDA-510, Руководство пользователя

Поделиться
Скачать
Fluke MDA-510 Скачать руководство пользователя страница 5

1

Introduction

The MDA-550/MDA-510 Motor Drive Analyzer (the Product 
or test tool) is an extension of the ScopeMeter

®

 Test Tool 

190 Series II with additional functionality and accessories 
that test inverter type motor drives. Inverter type motor 
drives are known as variable frequency drives or variable 
speed drives and use pulse width modulation to control ac 
motor speed and torque. The test tool supports motor drives 
with signal levels up to 1000 V to ground. 
For Motor Drive Analysis, the test tool provides:

•

Key motor drive parameters

Includes measurement of voltage, current, dc link 
voltage level and ac ripple, voltage and current 
unbalance, harmonics (MDA-550), and voltage 
modulation. 

•

Extended harmonics

Identifies the effects of low and high order harmonics on 
the electrical power system.

•

Guided measurements

Guidance for

 

motor drive input, dc bus, drive output, 

motor input, and shaft measurements (MDA-550).

•

Simplified measurement setup

Graphically shows how to connect and then 
automatically triggers according to the selected test 
procedure.

•

Reports

Use for troubleshooting and collaborative work with 
others.

•

Additional electrical parameters

Full 500 MHz oscilloscope capability is available for the 
complete range of electrical and electronic 
measurement on industrial systems.

This manual describes the functions of the Motor Drive 
Analyzer that are available when you select the Motor Drive 
Analyzer key. The functionality and specification for the 
Scope and Recorder modes are described in the 

ScopeMeter

®

 Test Tool 190 Series II Users Manual

.

The TrendPlot function in the Recorder mode plots a graph 
of selected Motor Drive readings over time.
Replace all references to the Meter key in the Users Manual 
with the Motor Drive Analyzer key. It is not possible to show 
large readings as described in the section 

Making 

Automatic Meter Measurements

 (for models 190-xx4). 

However, it is possible to show readings together with the 
waveform as described in the section 

Making Automatic 

Scope Measurements

.

The Motor Drive Analyzer is based on the ScopeMeter test 
tool model 190-504. All references to models 190-xx2 can 
be ignored.
The BC190/830 is the model number for the power adapter 
that complies with new regulations.

Содержание MDA-510





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды