Fike TWINFLEX SRP 100-0001 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 78

background image

TWINFLEX

®

SRP Control Panel Engineering and Commissioning Manual

52

Allows inputs

1 - 5 to be verified. Indicates status of input.

Blank = input is not configured
N

= switch is not active (see page 18)

A

= switch is active

S

= circuit is shorted

O

= circuit is open

This allows the time and date to be adjusted. Use the

LEFT

and

RIGHT

arrow keys to move the cursor between digits and the

UP

and

DOWN

arrow keys or the number keys to change values. Press the

ENTER

key to confirm the change.

The date is displayed using the format set in Set Date Format in the
Time And Date menu.

Note: If the SRP panel is powered down it will not retain the time
and date. The correct time and date will need to be re-
programmed after the panel is powered up.

This allows the date format to be set.
Formats allowed: YYYY-MM-DD, MM-DD-YYYY, DD-MM-YYYY
(default = DD-MM-YYYY)

This allows the Daylight Saving Time to be set.
DST: Allows DST to be turned on or off
MONTH: Set what month DST activates for forward or backward
DAY: Set the day of the week on which DST activates and in what
week of the month (1

st

, 2

nd

, 3

rd

, 4

th

, L (Last)).

TIME: Set what hour of the day DST activates.

Enable or Disable all Relay outputs.
Mode: Enable or Disable (default = enable)

3. Test Modes

5. Test Inputs

4 Time And Date

1 Set Time & Date

4 Time And Date

2 Set Date Format

4. Time And Date

3 DST Settings

5 Enable/ Disable

1 Relays

TEST INPUT
1 2 3 4 5
N N N N N
Esc to return

SET DATE FORMAT
STYLE: DD-MM-YYYY

↑/↓ /

→ /← /

Enter

/

Esc

DST:        Off  FWD BACK
MONTH:         Mar     Oct
DAY:           Sun L     Sun L
TIME:          01:00      01:00

SET TIME & DATE
TIME: 13:10
DATE: 2014/03/17

↑/↓ /

→ /← /

ENTER

/

Esc

ENABLE/DISABLE
RELAY: 01
MODE: Enable

↑/↓ /

→ /← /

Enter

/

Esc

«
...
50
51
52
53
54
...
»

Содержание TWINFLEX SRP 100-0001















































































Отзывы:

Нет отзывов

Похожие инструкции для TWINFLEX SRP 100-0001

Бренд: U-Prox Страницы: 31

Бренд: BEIER-Electronic Страницы: 22

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: CALEFFI Страницы: 12

QuickSetter+ 132 Series

Бренд: CALEFFI Страницы: 5

Бренд: Data I/O Страницы: 88

Бренд: Data Aire Страницы: 13

Бренд: Fagor Страницы: 10

Бренд: Fagor Страницы: 358

Бренд: Fagor Страницы: 556

Бренд: Fagor Страницы: 172

Бренд: Fagor Страницы: 180

Бренд: Fagor Страницы: 112

Master Control Unit

Бренд: FaderMate Страницы: 36

Бренд: GBD Страницы: 15

Бренд: WAREMA Страницы: 4

FEBCO 860 Small Series

Бренд: Watts Страницы: 12

Бренд: Bardiani Valvole Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды