Fike TWINFLEX SRP 100-0001 Скачать руководство пользователя страница 40

Страница: 40 / 78

TWINFLEX

SRP Control Panel Engineering and Commissioning Manual

The Test Keypad function enables the user to select each button to
ensure the correct function is shown on the screen. Press the

Esc

key

TWICE

to exit the menu.

This allows the time and date to be adjusted. Use the

LEFT

and

RIGHT

arrow

keys to move the cursor between digits and the

and

DOWN

arrow keys or the number keys to change values. Press the

ENTER

key to confirm the change.

The date is displayed using the format set in Set Date Format in the
Time And Date menu.

Note: If the SRP panel is powered down it will not retain the time
and date. The correct time and date will need to be re-
programmed after the panel is powered up.

3 Test Modes

1 Test Ctrls & Disp

4 Keypad

4 Time And Date

1 Set Time & Date

KEYPAD TEST
“SILENCE ALARMS”
IS BEING PRESSED
Esc & Esc to End Test

SET TIME & DATE
TIME: 13:10
DATE: 2014/03/17

↑/↓ /

→ /← /

Enter

Esc

Содержание TWINFLEX SRP 100-0001















































































Результаты поиска

Содержание TWINFLEX SRP 100-0001

Отзывы:

Похожие инструкции для TWINFLEX SRP 100-0001

Бренды по названию

Популярные бренды

Fike TWINFLEX SRP 100-0001, Инструкция по монтажу и пусконаладке

Результаты поиска

Содержание TWINFLEX SRP 100-0001

Отзывы:

Похожие инструкции для TWINFLEX SRP 100-0001

Бренды по названию

Популярные бренды