Fike TWINFLEX SRP 100-0001 Скачать руководство пользователя страница 14

Страница: 14 / 78

TWINFLEX

SRP Control Panel Engineering and Commissioning Manual

System Wiring Schematic

The four zones can be configured in menu option 9 as follows:

Off,

Zone not in use.

Twinflex,

Twinflex detection zone, as shown in the schematic below

Conventional,  Conventional detection zone
Release IRM,  Impulse releasing module zone
Release SRM,  Solenoid releasing module zone

The following schematic may prove useful as an aid to understanding the cable requirements for the
system;

KEY TO SYMBOLS

TWINFLEX

Multipoint

TWINFLEX

Multipoint with Sounder

TWINFLEX

Manual Call Point

1-4 TWINFLEX

SRP

zones. Cabled in 2 core
1.5mm

Screened cable

complying with BS 5839:
Pt 1: 2002 Category 1.
Note: No EOL device is
required as EOL is set at
the end device.

3 x Monitored Outputs,
programmable as for
various panel states.
Requires

10kΩ EOL

for

notification or 3.3KΩ for
releasing.

4 x Programmable Relays
Max 2A @ 30V.

Fault Relay MAX 1A
@ 30V.

230 V 50Hz AC power
supply requires a
dedicated supply with a
local un-switched fused
spur in accordance
with BS5839 pt1: 2002

5 x monitored Inputs
programmable for multiple
functions.
Requires 3.3K

Ω EOL.

Requires

a 470Ω or 680Ω

resistor to activate.

2 auxiliary power outputs
(resettable or non-
resettable)

Remote Status
Indicator (8 max.)

Содержание TWINFLEX SRP 100-0001















































































Результаты поиска

Содержание TWINFLEX SRP 100-0001

Отзывы:

Бренды по названию

Популярные бренды

Fike TWINFLEX SRP 100-0001, Инструкция по монтажу и пусконаладке

Результаты поиска

Содержание TWINFLEX SRP 100-0001

Отзывы:

Бренды по названию

Популярные бренды