FIBARO FGR-223 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 34

FIBARO FGR-223 Скачать руководство пользователя страница 9

9

REMOVInG ThE DEVIcE

Removing (Exclusion)

- Z-Wave device learning mode, allowing to

remove the device from existing Z-Wave network.
Removing the device restores all the default parameters of the de-

vice, but does not reset power metering data.

#4: Removing the device

NOTE

In case of problems

with removing using

the S1 switch, use

B-button instead (lo-

cated on the housing).

i

To remove the device from the Z-Wave network:
1.  Make sure the device is powered.
2.  Identify the S1 switch.
3.  Set the main controller in remove mode (see the controller’s

manual).

4.  Quickly, triple click the S1 switch.
5.  Wait for the removing process to end.
6.  Successful removing will be confirmed by the Z-Wave controller’s

message.

NOTE

If parameter 40 ena-

bles scenes for triple

S1 click, disable it or

use B-button instead

to remove the device.

i

NOTE

If parameter 24 is set

to 1, use S2 switch in-

stead to remove the

device.

i

«
...
7
8
9
10
11
...
»

Содержание FGR-223



































Отзывы:

Нет отзывов