FIBARO FGR-223 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 34

FIBARO FGR-223 Скачать руководство пользователя страница 19

19

Z-WAVE RAnGE TEST

#12: Z-Wave range test

The device has a built in Z-Wave network main controller’s

range tester

.

Follow the below instructions to test the main controller’s range:
1.  Switch off the mains voltage (disable the fuse).
2.  Remove the device from the wall switch box.
3.  Switch on the mains voltage.
4.  Press and hold the B-button to enter the menu.
5.  Wait for the visual lED indicator to glow violet.
6.  Quickly release and click the B-button again.
7.  Visual indicator will indicate the Z-Wave network’s range (range

signalling modes described below).

8. To exit Z-Wave range test, click the B-button.

Z-Wave range tester signalling modes

:

Visual indicator pulsing green

- the device attempts to establish a

direct communication with the main controller. If a direct commu-

nication attempt fails, the device will try to establish a routed com-

munication, through other modules, which will be signalled by visual

indicator pulsing yellow.

Visual indicator glowing green

- the device communicates with the

main controller directly.

Visual indicator pulsing yellow

- the device tries to establish a rout-

ed communication with the main controller through other modules

(repeaters).

Visual indicator glowing yellow

- the device communicates with

the main controller through the other modules. After 2 seconds the

device will retry to establish a direct communication with the main

controller, which will be signalled with visual indicator pulsing green.

Visual indicator pulsing violet

- the device does communicate at the

maximum distance of the Z-Wave network. If connection proves suc-

cessful it will be confirmed with a yellow glow. It’s not recommended

to use the device at the range limit.

Visual indicator glowing red

- the device is not able to connect to

the main controller directly or through another Z-Wave network de-

vice (repeater).

CAUTION

To make Z-Wave range

test possible, the de-

vice must be added

to the Z-Wave control-

ler. Testing may stress

the network, so it is

recommended to per-

form the test only in

special cases.

!

NOTE

communication mode

of the device may

switch between direct

and one using rout-

ing, especially if the

device is on the limit

of the direct range.

i

«
...
17
18
19
20
21
...
»

Содержание FGR-223



































Отзывы:

Нет отзывов