manualshive.com logo in svg

FIBARO FGR-223, Руководство по эксплуатации, Страница: 25 / 34

Поделиться
Скачать
FIBARO FGR-223 Скачать руководство пользователя страница 25

25

ADVAncED PARAMETERS

30. Alarm configuration - 1st slot

This parameter determines to which alarm frames and how the device 

should react. The parameters consist of 4 bytes, three most significant 

bytes are set according to the official Z-Wave protocol specification.

Available settings:

1B

 [MSB] - notification Type

2B

 - notification Status

3B

 - Event/State Parameters

4B

 [lSB] - action:

0

 - no action

1

 - open blinds

2

 - close blinds

Default setting: 

[0x00, 0x00, 0x00, 0x00]

(disabled)

Parameter size:

4

 [bytes]

31. Alarm configuration - 2nd slot (Water)

This parameter determines to which alarm frames and how the device 

should react. The parameters consist of 4 bytes, three most significant 

bytes are set according to the official Z-Wave protocol specification.

Available settings:

1B

 [MSB] - notification Type

2B

 - notification Status

3B

 - Event/State Parameters

4B

 [lSB] - action:

0

 - no action

1

 - open blinds

2

 - close blinds

Default setting: 

[0x05, 0xFF, 0x00, 0x00]

(Water Alarm, any notification, no action)

Parameter size:

4

 [bytes]

ALARM CONFIGURATION

NOTE

Alarm with lower 

number has the high-

er priority, thus first 

alarm will override 

other alarms with the 

same type.

i

NOTE

Setting notification 

Value to 0xFF will re-

sult in launching the 

action twice: when 

alarm occurs and is 

cancelled.

i

Содержание FGR-223



































Отзывы:

Нет отзывов