manualshive.com logo in svg

FIBARO FGR-223, Руководство по эксплуатации, Страница: 8 / 34

Поделиться
Скачать
FIBARO FGR-223 Скачать руководство пользователя страница 8

8

ADDInG ThE DEVIcE

#3: Adding the device

Adding (Inclusion)

 - Z-Wave device learning mode, allowing to add 

the device to existing Z-Wave network.

To add the device to the Z-Wave network 

manually

:

1.  Power the device.
2.  Identify the S1 switch.
3.  Set the main controller in (Security/non-Security Mode) add mode 

(see the controller’s manual).

4.  Quickly, triple click the S1 switch.
5.  If you are adding in Security S2 Authenticated, scan the DSK QR 

code or input the 5-digit PIn code (label on the bottom of the 

box).

6.  Wait for the adding process to end.
7.  Successful adding will be confirmed by the Z-Wave controller’s 

message.

NOTE

In case of problems 

with adding using the 

S1 switch, use B-but-

ton instead (located 

on the housing).

i

NOTE

SmartStart

 ena-

bled products can be 

added to SmartStart 

enabled Z-Wave con-

troller by scanning 

the Z-Wave QR code 

present on the prod-

uct. SmartStart prod-

uct will be added 

automatically within 

10 minutes of being 

switched on in the 

network range.

i

To add the device to the Z-Wave network 

using Smart Start

:

1.  Set the main controller in Security S2 Authenticated add mode 

(see the controller’s manual). 

2.  Scan the DSK QR code or input the 5-digit PIn code (label on the 

bottom of the box)

3.  Power the device (turn on the mains voltage).
4.  lED will start blinking yellow, wait for the adding process to end.
5.  Successful adding will be confirmed by the Z-Wave controller’s 

message.

Содержание FGR-223



































Отзывы:

Нет отзывов