manualshive.com logo in svg

FIBARO FGR-223, Руководство по эксплуатации, Страница: 2 / 34

Поделиться
Скачать
FIBARO FGR-223 Скачать руководство пользователя страница 2

2

 

Important safety information

Read this manual before attempting to install the device!

 

Failure to observe recommendations included in this manual 

may be dangerous or cause a violation of the law. The manufacturer, 

Fibar Group S.A. will not be held responsible for any loss or damage 

resulting from not following the instructions of operating manual.

!

Danger of electrocution! 

FIBARO Roller Shutter 3 is designed to operate in electrical 

home installation. Faulty connection or use may result in fire or elec-

tric shock.
All works on the device may be performed only by a qualified and 

licensed electrician. Observe national regulations.
Even when the device is turned off, voltage may be present at its ter-

minals. Any maintenance introducing changes into the configuration 

of connections or the load must be always performed with disabled 

fuse.

Caution

It is not recommended to operate all of the roller blinds simul-

taneously. For safety reasons, at least one roller blind should be con-

trolled independently, providing safe escape route in case of emer-

gency.

!

Содержание FGR-223



































Отзывы:

Нет отзывов