Festo MSE6-E2M Скачать руководство пользователя страница 46

Страница: 46 / 84

Festo — MSE6-E2M — 2022-08d

Commissioning

6. Set the IP addressing with DIL switch 3.
7. Fit the cover.
8. Screw on the retaining screws hand-tight and then tighten to 0.4 Nm ± 10%.

Setting operating mode and protocol, DIL switch 1

The energy efficiency module only supports the Remote I/O operating mode with the bus node
CPX-FB36, factory setting.
All 1.1 and 1.2 switch elements of DIL switch 1 must be in the OFF position.

DIL switch 1.1

Setting operating mode

DIL 1.1: OFF
Factory setting

‘Remote I/O’ operating mode.

All functions of the energy efficiency module are controlled directly
by the controller or by a higher-level PLC.

DIL 1.1: ON

Not supported.

The 1.1 DIL switch element must be in the OFF position.

Tab. 30: Setting the operating mode with DIL switch 1.1

DIL switch 1.2

Setting the protocol

DIL 1.2: OFF
Factory setting

‘EtherNet/IP’ protocol.

The energy efficiency module uses the ‘EtherNet/IP’ protocol.

DIL 1.2: ON

Protocol ‘Modbus TCP’
The energy efficiency module uses the ‘Modbus TCP’ protocol.

Tab. 31: Setting the protocol with DIL switch 1.2

Setting diagnostic mode, DIL switch 2

DIL switch 2

Setting diagnostic mode

DIL 2.1: OFF
DIL 2.2: OFF
Factory setting

‘I/O diagnostics interface’ and status bits are switched off, + 0 byte
I/0 byte O.

DIL 2.1: OFF
DIL 2.2: ON

The status bits are on, + 1 byte I/0 byte O

Содержание MSE6-E2M




















































































Результаты поиска

Содержание MSE6-E2M

Отзывы:

Похожие инструкции для MSE6-E2M

Бренды по названию

Популярные бренды

Festo MSE6-E2M, Руководство по эксплуатации

Результаты поиска

Содержание MSE6-E2M

Отзывы:

Похожие инструкции для MSE6-E2M

Бренды по названию

Популярные бренды