Festo MSE6-E2M Скачать руководство пользователя страница 53

Страница: 53 / 84

Festo — MSE6-E2M — 2022-08d

Commissioning

RJ45 bushing

Pin

Signal

Explanation

n.c.

Not connected

Housing

Shield/FE Shield/functional earth

Tab. 38: Pin allocation of the network interfaces RJ45, PROFINET

Connecting the energy efficiency module to the network
1. Connect the bus node to the network with the NECU-MS-D12G4-C2-ET or FBS-RJ45-PP-GS con-

nector.

2. Seal the unused connections with cover caps or blanking plugs to achieve the specified degree of

protection.

8.6.4

Setting DIL switches

You can set the following parameters with the DIL switches:

–

The operating mode. The energy efficiency module only supports the Remote I/O operating mode in
conjunction with the bus node CPX(-M)-FB44.

–

The diagnostics mode.

Fig. 28: DIL switches on bus node CPX-M-FB44

DIL switch 1: operating mode

DIL switch 2: diagnostic mode

Memory card

1. Switch off the power supply.
2. Unscrew the retaining screws of the cover.
3. Remove the cover

2 DIL switches are visible.

4. Use DIL switch 1 to set the operating mode.
5. Set the diagnostic mode with DIL switch 2.
6. Fit the cover.
7. Tighten the retaining screws of the cover. Tightening torque: 0.4 Nm ± 10 %.

Содержание MSE6-E2M




















































































Результаты поиска

Содержание MSE6-E2M

Отзывы:

Похожие инструкции для MSE6-E2M

Бренды по названию

Популярные бренды

Festo MSE6-E2M, Руководство по эксплуатации

Результаты поиска

Содержание MSE6-E2M

Отзывы:

Похожие инструкции для MSE6-E2M

Бренды по названию

Популярные бренды