Festo MSE6-E2M Скачать руководство пользователя страница 43

Страница: 43 / 84

Festo — MSE6-E2M — 2022-08d

Commissioning

8.4

Commissioning with bus node CPX-M-FB36

This section describes the interfaces, DIL switches and display elements of the bus node mentioned
and provides an overview of the configuration and commissioning with this bus node.

For detailed information on the bus node, see the documentation on the bus account

1 Applicable documents.

A configuration for the energy efficiency module can be created using the software ‘Festo Maintenance
Tool’, CPX-FMT

8.4.4 Commissioning and configuration.

8.4.1

Interfaces and display components

Interfaces and display components on the bus node CPX-M-FB36

Fig. 23: Interfaces and display components on

the bus node CPX-M-FB36

Service interface

Network-specific and CPX-specific LEDs

Network port, M12, D-coded

DIL switch, under the cover

LED displays on the bus node CPX-M-FB36

Fig. 24: LED displays on the bus node CPX-M-

FB36

Network-specific LEDs

CPX-specific LEDs

Содержание MSE6-E2M




















































































Результаты поиска

Содержание MSE6-E2M

Отзывы:

Похожие инструкции для MSE6-E2M

Бренды по названию

Популярные бренды

Festo MSE6-E2M, Руководство по эксплуатации

Результаты поиска

Содержание MSE6-E2M

Отзывы:

Похожие инструкции для MSE6-E2M

Бренды по названию

Популярные бренды