12
EN
NOTE:
Measurements were obtained in compliance with
UNI 7712, ISO 3740, ISO 3746 and ECC 89/392 rules.
When cutting aluminium the use of protective
earphones or ear plugs is absolutely necessary.
The use of this gear is also recommended for all
other uses.
1.8
INFORMATION ABOUT THE ELECTROMAGNETIC
COMPATIBILITY
The European regulations on safety and, in particular, the
EEC Directive 89/336 contemplate that all the equipment be
equipped with shielding devices against radio interferences
both from and towards the outside.
This machine is safe and in compliance with above
regulations.
Tests were carried out according to EN 55011, EN 50081-1
regulations.
1.9
MACHINE DESCRIPTION (Fig.1)
The mitre-saw machine consists of three basic parts : the
machine body complete with motor
6
which is integrated into
lower part
3
by means of the joint
4
and the swivel support
5
,
and the upper work unit consisting of the work table
15
, the
rest square
17
and the movable blade cover
16
.
The base
3
is used as rest when cutting and butting operations
have to be carried out in the different available angles; the
upper table is used as rest when trimming or sectioning wood
tables of huge dimensions and, in particular, when cutting
wood along grain.
Legend Fig. 1
1
- Control handgrip
A
-Trademark plate / CE plate
2
- Main switch start button
B
-Accident-prevention plate
3
- Base
C
- Specification plate
4
- Body/base swivel joint
5
- Rotating bearing
6
- Motor
7
- Blade
8
- Lever to unblock graduation
9
- Button to unblock body descent
10
- Permanent blade shield
11
- Movable blade shield
12
- Bar clamp shaft
13
- Dust exhaust manifold
14
- Main switch release device
15
- Upper work surface
16
- Movable upper safety guard
17
- Bearing bracket
18
- Support feet
19
- Transport locking pin
20
- Angle rest at 90°
21
- Main switch locking device
1.5
STANDARD SAFETY PROCEDURE
–
Remove all cuttings from the work surface ensuring it is
completely clean.
–
Use the machine in dry areas and away from inflammable
substances or gas.
–
Do not use the machine outdoors in adverse weather or
environmental conditions (explosive atmospheres,
storms or rain).
–
Wear appropriate clothing: do not wear loose-sleeved
garments or objects such as scarves, chains or bracelets
which may get caught in machine’s moving parts.
–
Always use personal protective gear: standard accident-
prevention goggles, well-fitting gloves, earphones or
earplugs and headgear to cover hair if necessary.
–
Handle the power supply cable with care: do not use it to
lift the machine or to pull the plug out of the socket. Keep
it away from cutting edges, oily patches and high
temperatures.
–
Keep the machine out of reach of children: do not allow
them to approach or touch the machine.
–
When in need, only use approved power supply cable
extensions.
–
Beware of electrification: avoid all contact with earthed
objects such as pipes, radiators and refrigerators.
1.6
SAFETY PROCEDURE FOR FURTHER RISKS
–
Do not force the machine unnecessarily: excessive cutting
pressure may lead to rapid deterioration of the blade and
a decrease in performance in terms of finish and cutting
precision.
–
When cutting aluminium and plastics always use the
appropriate clamps: all workpieces must be clamped
down firmly.
–
Avoid accidental starts: do not press the start button while
inserting the plug into the socket.
–
Always use the tools recommended in this manual to
obtain the best results from your cutting-off machine.
–
Always keep hands away from the work area when the
machine is running; before performing tasks of any kind
release the main switch button located on the handgrip,
thus disconnecting the machine.
–
Always keep hands away from the work area when the
machine is running; before performing tasks of any kind
release the main switch button located on the handgrip,
thus disconnecting the machine.
1.7
NOISE CONDITIONS
Idling
Equivalent sound level .................................. Leq = 75 dB(A)
Running with full load
Transverse cutting of hard wood (maple wood) mm.50x80
Equivalent sound level ............................... Leq = 81,7 dB(A)
Cutting of section aluminium 40x40 mm. thickness 2 mm.
Equivalent sound level ............................... Leq = 89,1 dB(A)
Average sound level ................................. Lpm = 82,7 dB(A)
Environmental correction factor ....................... K = 3,9 dB(A)
Normalized sound power ........................... Lwa = 97,4 dB(A)
These tests were performed with a standard blade Z=48 to
cut wood and with a special blade Z=96 to cut aluminium,
always with the machine positioned on the work bench.
The frequency root mean RMS weighed for hand-arm
acceleration does not exceed 2.5m/s².
