Fastwel CPC522 Скачать руководство пользователя

Страница: 13 / 58

CPC522

CPC522 User Manual

Note

For all versions of the CPC522, forced cooling must be provided.

1.2

Technical specifications

●

Processor

•

Intel Coffee Lake H, E-2276ML 2 GHz, 25W, 6 x cores, 12 MB cache (CPC522-01);

•

Intel Coffee Lake H, Core i3-9100HL 1.6 GHz, 25W, 4 x cores, 6 MB cache

(CPC522-02)

●

RAM

•

DDR4-2666 with ECC 16 GB, soldered, two-channel (for CPC522-01);

•

DDR4-2666 with ECC 8 GB, soldered, two-channel (for CPC522-02);

●



Integrated Graphics Card

Intel® UHD Graphics P630

•

Base frequency

– 350 MHz;

•

Graphics Maximum Dynamic Frequency

– 1.15 GHz;

•

Maximum memory size supported by the processor

– 64 GB;

•

Supported

4К@60 Hz;

•

2 x DisplayPort outputs (resolution up to 4096x2304@60Hz) are routed to the front

panel;

•

1 x DisplayPort interface is routed to the front panel connector;

●



LPC Bus

•

Routed to the mezzanine connector;

●



PCI-E Bus

•

Processor hosts. Support of PCI-E 3.0 (up to 8 GT/s);

- Routed to the backplane connector's with support of up two x8 devices;

•

PCH hosts. Support of PCI-E 3.0 (up to 8 GT/s). Up to 10 PCI Express ports;

- 8 x lines are routed to the backplane connector with support of up to two

х4 devices;

- 4 x lines are routed to the backplane connector with support of up to four

х1 devices;

- 2 x lines are routed to the mezzanine connector with support of two

х1 devices or one

х2 device. Can be configured as one or two SATA III interfaces depending on M2

interface configuration.

- 2 x lines are routed to the M2 drive connector. One line can be configured as a SATA

III interface depending on the type of drive installed.

- 2 x lines are used by 2.5 Gb Ethernet controllers.

●



SMBus

•

Compatibility with the 2.0 specification;

•

Speed up to 100 Kb/s;

●



FLASH BIOS

Содержание CPC522



























































Результаты поиска

Содержание CPC522

Отзывы:

Похожие инструкции для CPC522

Бренды по названию

Популярные бренды

Fastwel CPC522, Руководство пользователя

Результаты поиска

Содержание CPC522

Отзывы:

Похожие инструкции для CPC522

Бренды по названию

Популярные бренды