Fastwel CPC522 Скачать руководство пользователя

Страница: 14 / 58

CPC522

CPC522 User Manual

•

2x 128 Mb SPI-Flash;

●

SATA III interface

•

Five ports are routed to the backplane connectors;

•

Two ports that are multiplexed with PCI Express interface, are routed to the

mezzanine connector;

•

One port is used by an internal SATA drive;

•

One SATA III port can be used by an M2 interface depending on the type of drive

installed.

●

Integrated SATA SSD

•

32 GB 3D NAND Flash;

•

Interface: SATA III;

●

2 x ports LAN 10BASE-Te, 100BASE-TX, 1000BASE-T and 2500BASE-T

•

The two ports are routed to the front panel connectors;

●

USB ports

•

6 x USB 3.1 ports (10 Mb/s):

- 2 x ports are routed to the front panel connectors;

- 4 x ports are routed to the backplane connectors;

•

12 x USB 2.0 ports:

- 8 x ports are routed to the backplane connectors;

- 2 x ports are routed to the front panel connectors;

- 2 x ports are routed to the mezzanine connector;

●

FRAM

•

32 KB (1 KB for storing BIOS Setup settings and serial number of the device);

•

Implemented on the SPI FPGA bus;

●

Real-Time Clock

•

Powered from the lithium battery CR2032 (3V);

●

Audio support

•

HD Audio interface is routed to the mezzanine connector

●

Watchdog timer

•

Internal timer with a possibility of software-based control

●

SGPIO interface

•

Signaling support in accordance with the SFF-8485 specification;

●

Hardware monitoring

•

Implemented via SMBus interface;

•

Monitoring of three supply voltages;

•

Monitoring of CPU temperature;

•

Monitoring of PCB temperature;

•

Power monitoring;

●

LED indication

The LEDs indicators for start diagnostics, drives activity, user LEDs are routed to the front panel.

The LEDs are described in the table below.

Содержание CPC522



























































Результаты поиска

Содержание CPC522

Отзывы:

Похожие инструкции для CPC522

Бренды по названию

Популярные бренды

Fastwel CPC522, Руководство пользователя

Результаты поиска

Содержание CPC522

Отзывы:

Похожие инструкции для CPC522

Бренды по названию

Популярные бренды