Farmet FALCON 3 Скачать руководство пользователя

Страница: 91 / 102

Machine-specific alarms

Alarm text

Possible cause

Possible remedy

602

Connection lost.

The connection to the ERC module
has been lost.

Check the cables.

603

Connection disrupted.

The connection to the ERC module is
interrupted.

Check the cables.

604

Supply voltage too low.

The supply voltage of the ERC
modules is too low.

Check the supply voltage and check
the vehicle battery.

605

Short circuit.

There is a short circuit in the ERC
modules.

Check the cables.

606

Open load current circuit.

An open load circuit has been
detected for the ERC modules.

Check the cables and make sure the
disconnect connector is available.

607

Recognizes. ERC module error.

The configuration is incorrect.

Check the IN and OUT configuration.

608

Seed flow was not recognized.

The seed flow system did not detect
any seed flow.

Check the seed flow system.

609

Seed flow was detected.

Seed flow occurred in the tramline.

Check the tramline switching. Kalpak
tightness check.

611

Low tank level.

There is little seed of fertilizer in the
hopper.

Fill the hopper.

612

The tank is empty.

There is no seed or fertilizer in the
hopper.

Fill the hopper.

613

Exceeding the time when closing
the section.

It takes too long to close the left
section.

Make sure something is blocked.

617

Defective charger.

The charger alternator is defective.

Check the charger alternator.

618

No product flow was detected in the
active row.

Check the product flow, or some
supply lines are blocked.

619

Too high flow detected in the active
row.

Product flow detected too high was
detected in the active row.

Check the calibration.

620

Product flow too low in the active
row detected.

Too little product flow was detected in
the active row.

Check the calibration.

Содержание FALCON 3







































































































Результаты поиска

Содержание FALCON 3

Отзывы:

Похожие инструкции для FALCON 3

Бренды по названию

Популярные бренды

Farmet FALCON 3, Руководство по эксплуатации

Результаты поиска

Содержание FALCON 3

Отзывы:

Похожие инструкции для FALCON 3

Бренды по названию

Популярные бренды