Farmet FALCON 3 Скачать руководство пользователя

Страница: 92 / 102

Alarm text

Possible cause

Possible remedy

621

Not available for this product no
dataset.

A calibration test has not yet been
performed for the product in question.

Perform a calibration test before
working with the product.

622

The sowing test button is activated.

The sowing test button was activated
before opening the calibration screen.

Release the sowing test button.

630

Connection lost.

The connection to the MRC module
has been lost.

Check the cables.

631

Undefined module index.

A software error has occurred.

Contact customer service.

636

There is no seed for overdosing.

Too little seed was detected during
pre-dosing.

Make sure that sufficient seed is
available.

638

The engine stopped.

The MRC engine stopped.

Check the cables.

639

Current too high.

The MRC motor requires too much
current.

Make sure something is blocked.

640

No speed was reached.

The MRC module did not reach the
required speed.

Check the cables. Check the seed
drills.

641

Power voltage too low.

The power voltage of the MRC
module is too low.

Check the cables.

642

Electronics voltage too low.

The electronics voltage at the MRC
module is too low.

Check the cables.

643

Sensor voltage too low.

The sensor voltage at the MRC
module is too low.

Check the cables.

650

Connection lost.

The connection to the

AIRidium®

sensor has been disconnected.

Check the cables.

651

Undefined module index.

An error occurred of the

AIRidium®

module.

Contact customer service.

660

Connection lost.

The connection to the CAN Repeater
has been disconnected.

Check the cables.

663

Drop below minimum voltage.

The voltage is lower than the pre-set
minimum supply voltage.

Check wiring and supply voltage.

664

Sensor error detected
PLANTirium®. Pollution rate too
high.

The sensor is dirty. Sensitivity does
not match the selected product.

Clean the sensor and/or change
the sensitivity in the product.

665

An error has been detected in the
PLANTirium® sensor. Faulty
sensor transmitter.

The sensor transmitter is defective.

Check the cables on the sensor.

666

An error has been detected in the
PLANTirium® sensor. Not
achieved.

The minimum supply voltage has not
been reached.

Check the cables.

Содержание FALCON 3







































































































Результаты поиска

Содержание FALCON 3

Отзывы:

Похожие инструкции для FALCON 3

Бренды по названию

Популярные бренды

Farmet FALCON 3, Руководство по эксплуатации

Результаты поиска

Содержание FALCON 3

Отзывы:

Похожие инструкции для FALCON 3

Бренды по названию

Популярные бренды