Farmet FALCON 3 Скачать руководство пользователя

Страница: 87 / 102

Error messages

ISO messages

Alarm text

Possible cause

Possible remedy

001

The system has been stopped. A

restart is required.

The connection to the SLAVE slave

control unit has been interrupted.

Download manager has been

activated.

Disconnect and connect the control unit

(disconnect the ISO connector).

002

The configuration has changed. The

job computer restarts.

The configuration has changed.

Wait until the control unit restarts.

003

Input too high.

The value entered is too high.

Enter a lower value.

004

Input too low.

The value entered is too low.

Enter a higher value.

005

Error reading or writing data in flash

memory of EEPROM.

An error occurred while starting the job

computer.

Disconnect and connect the control unit

(disconnect the ISO connector).

006

Data was successfully downloaded.

007

A configuration error has been

detected.

The configuration is incorrect.

Check the configuration.

008

The procedure is not permitted as long

as the job is activated in the ISOBUS-

TC application.

The job is activated in the ISOBUS-TC

application.

Deactivate the order.

009

Speed signal lost from CAN bus.

The cable connection has been

disconnected.

Check the cable connection.

010

Error initializing Control-Layer

The control-layer was incorrectly

configured.

Check the configuration.

011

Multiple terminals have the same

number.

There are several terminals with the
same number (function instance) on

ISOBUS.

Change the number (function instance)

in the terminal.

012

Multiple TASK controllers have the

same number.

There are several TASK controllers

with the same number on ISOBUS.

Change the number.

013

The list of orders is full.

Too many orders are available in the

order list.

Delete unnecessary orders.

014

Internal order recording stopped due

to product change.

The product was changed during the

recording of the internal order.

Select the original product.

015

The order failed to run because

another product was assigned.

A different product that the one

assigned to the tank in the

configuration is stored in the order.

Check which product is correct and

correct the order or assignment to

hopper.

Содержание FALCON 3







































































































Результаты поиска

Содержание FALCON 3

Отзывы:

Похожие инструкции для FALCON 3

Бренды по названию

Популярные бренды

Farmet FALCON 3, Руководство по эксплуатации

Результаты поиска

Содержание FALCON 3

Отзывы:

Похожие инструкции для FALCON 3

Бренды по названию

Популярные бренды