Farmet FALCON 3 Скачать руководство пользователя

Страница: 68 / 102

If the machine is raised, the pressure is too high = lower the pressure.

The pressure must always be set according to the soil conditions.

If the pressure is too low, the sowing depth may be unevenly distributed.

17.2.1

Increase the pressure

1. Apply pressure to and leave it closed.
2. Use the wheel to gradually tighten the pressure reducing valve to increase the coulter

pressure.

3. Again drive a few meters and check the seed placement depth.

17.2.2

Lowering the pressure

1. For lowering the pressure, raise the seed section to the upper position with

2.  Releasing the pressure reducing valve reduces the pressure.
3.  Lower the sowing section to the working position with       .
4.  Check the reduced pressure on the manometer.
5.  Again drive a few meters and check the seed placement depth.

Содержание FALCON 3







































































































Результаты поиска

Содержание FALCON 3

Отзывы:

Похожие инструкции для FALCON 3

Бренды по названию

Популярные бренды

Farmet FALCON 3, Руководство по эксплуатации

Результаты поиска

Содержание FALCON 3

Отзывы:

Похожие инструкции для FALCON 3

Бренды по названию

Популярные бренды