Farmet FALCON 3 Скачать руководство пользователя

Страница: 89 / 102

Regulations alarms

Alarm text

Possible cause

Possible remedy

400

The configured required blower

speed is invalid. Product: xxxx.

The set required speed is outside the

specified fan drive limits for the

respective product.

Change the minimum and maximum

limits of the required product speed.

401

The blower rotates too slowly.

The current fan speed is lower than

the minimum allowed.

Increase fan speed.

Alarm text

Possible cause

Possible remedy

402

The blower rotates too fast.

The current fan speed is higher than the

value entered in the parameter

„Blower

speed tolerance“.

Reduce the fan speed or change the

tolerance limit.

403

Pressure too high.

The pressure of the linear encoder is

higher than the value of the

“Maximum

value” parameter.

Reduce the pressure or change the

parameter “Maximum value”.

404

Pressure too low.

The pressure of the linear encoder is

lower than the value of the “Minimum

value” parameter.

Increase pressure or change

parameter

“Minimum value”.

405

Dosing has been stopped since the

working position has not been

reached. Excavate the sowing

section.

The machine is not in the working

position.

Excavate the sowing section.

406

Dosing was stopped because the

machine was not completely raised.

Excavate the sowing section.

The machine was not fully raised.

Excavate the sowing section.

407

The dispenser drive is stopped.

The current speed of the dosing drive is

lower than the minimum speed.

Stop now! Eliminate the cause.

408

The metering shaft is stationary.

Speed sensor on the dosing shaft does

not register any movement of the dosing

shaft.

Stop now! Eliminate the cause.

410

The dispenser drive is outside the

control area.

The current dosing drive speed is higher

or lower than set speed.

Drive slower/faster or use a

larger/smaller metering unit.

411

The dosing drive cannot comply

with the setpoint.

You are driving too fast or too slow. It is
not possible to reach the required value

at the current speed.

Drive slower or faster so she can

control unit to regulate the sowing

rate.

412

The application has stopped due to

a fatal error.

An error has occurred. This error always

occurs in combination with another

error.

Please fix the related error.

413

The application was stopped due to

high driving speed.

Driving speed is too high.

Reduce the speed.

Содержание FALCON 3







































































































Результаты поиска

Содержание FALCON 3

Отзывы:

Похожие инструкции для FALCON 3

Бренды по названию

Популярные бренды

Farmet FALCON 3, Руководство по эксплуатации

Результаты поиска

Содержание FALCON 3

Отзывы:

Похожие инструкции для FALCON 3

Бренды по названию

Популярные бренды