![background image](http://html1.mh-extra.com/html/faac/e600/e600_manual_3131671014.webp)
14
OPEN B
OPEN A
RADIO SET UP
ENGLISH
The 3 types of radio codes (DS, LSH, LC) cannot
coexist.
Only one radio code can be used at a time.
To change over from one code to another, you must
delete the existing one (see paragraph on deletion),
and repeat the memory-storage procedure.
A maximum of two codes can be stored. One on the
OPEN A channel and one on the OPEN B channel
1) On the DS radio control, select the required ON-OFF combination
for the 12 dip-switches.
2) To respectively memory store total or partial opening, press
the OPEN A or OPEN B push-button for one second (Fig. 31
ref.
)
3) The relevant LED (Fig. 31 ref
), begins to flash for 5 sec.
12.1 Memory storage of radio controls DS
Fig. 30
12 MEMORY STORAGE OF RADIO CONTROLS CODING
The control unit has an integrated 2-channel decoding system
(DS, SLH, LC) named OMNIDEC. This system makes it possible to
memory-store both total opening (OPEN A) and partial opening
(OPEN B) of the automated system - this is made possible by an
additional receiver module (Fig. 30 ref.
) and radio controls
on the same frequency.
4) Within these 5 secs., press the appropriate push-button on
the radio control.
5) The relevant LED lights up on steady beam for 1 second and
then goes OFF, indicating that storage was executed.
6) To add other radio controls, set the same ON - OFF combination
used in point 1).
12.2 Memory storage of radio controls SLH
A Maximum of 250 codes can be memory stored, split
between OPEN A and OPEN B.
1) On the SLH radio control, simultaneously press and hold down
push-buttons P1 and P2.
2) The radio control LED begins to flash.
3) Release both push-buttons.
4) To respectively memory store total or partial opening, press
the OPEN A or OPEN B push-button for one second (Fig. 31
ref.
).
5) The relevant LED starts to flash slowly for 5 sec.
6) Within these 5 sec., while the radio control LED is still flashing,
press and hold down the required push-button on the radio
control (the radio control LED lights up on steady beam).
7) The LED on the board lights up on steady beam for 1 second
and then goes OFF, indicating that storage was executed.
8) Release the radio control push-button.
9) Quickly press twice in succession the memory stored radio
control push-button.
The automated system performs one opening operation.
Make sure that the automated system is free of any
obstacle created by persons or things.
10) To add other radio controls, transfer the code of the
memory-stored push-button of the radio control to the
relevant push-button of the radio controls to be added,
observing the following procedure:
- On the memory stored radio control, simultaneously press and
hold down push-buttons P1 and P2.
- The radio control LED begins to flash.
- Release both push-buttons.
- Press and hold down the memory-stored push-button (the radio
control LED lights up on steady beam).
- Approach the radio controls to each other and hold down the
push-button corresponding to the radio control to be added;
then release it after a double flash of the radio control LED
indicating that storage was executed.
- Quickly press twice in succession the memory stored radio
control push-button
.
The automated system performs one opening operation.
Make sure that the automated system is free of any
obstacle created by persons or things.
12.3 Memory storage of radio controls LC (for some markets
only)
A Maximum of 250 codes can be memory stored, split
between OPEN A and OPEN B.
1) Use LC remote controls only with receiver module at 433
MHz.
2) To respectively memory store total or partial opening, press
the OPEN A or OPEN B push-button for one second (Fig. 31
ref.
).
3) The relevant LED starts to flash slowly for 5 sec.
Fig. 31