EYELA LTI- 400E Скачать руководство пользователя

Страница: 50 / 62

-47-

After executing defrosting (forced manual defrosting) or

maintenance and checking procedures, it is useful to learn

the next timing by resetting the values.

※

Factory default value

：

0 hour

※

In total operation hours display, [Alarm] lamp

lights up when setting time elapses and indicator

displays [Addt] and measured temperature

alternately, and the unit is under control.

Displaying total operation hours and resetting

1)Press [Set] key for longer than 5 sec. while the unit is

controlled to enter into adjustment mode. Then, the

indicator displays [SnS] and the mode changes to

calibrating displayed temperature mode.

・「

Temperature display lamp

（℃）」

turns off a

light.

2)Press

［▲］

key 6 times to enter into total operation

hours display and reset mode

［

Addt

］

3)Press

［

Set

］

key.

Indicator changes to display total operation hour

(blinking).

※

Total operation hours describes the elapsed time

after starting running the unit. Factory default value

「

0hr.

」

4)To reset the total operation hour, press

［▲］

key.

Then, the indicator changes to display

「

cLr

」

（

blinking).

［

Total operation hours

］

［▲］↓ ↑［▼］

［

cLr

］：

Reset can be executed.

※

If you do not need to reset, press

［▼］

key to

change the display of indicator to total operation
hours display (blinking) and press [Set] key for
longer than 5 sec. to display measured
temperature. Then, resetting can not be executed.

5) Pressing [Set] key for longer than 5 sec. while

「

cLr

」

is
displayed can display measured temperature on the
indicator and the values can be reset.

※

Values will not be reset until you press

［

Set

］

key for

longer than 5 sec.

※

To change other adjustment mode, press

［▲］

［▼］

key to display the mode you' d like to change.

※

If you don't need to change the other adjustment

mode, press [Set] lye for longer than 5 sec. Then,

indicator changes to display [Measured temperature].

※

If no key operation is done for longer than a minute

while setting, the display returns to measured

temperature. In such a case, please reset the setting

1) Press［Set］ key for longer than
5 sec. to enter into adjustment
mode.

2)Moves to total
operation hours display and
resets

3)Total operation hours display

4)Resetting total operation hours display

5)Values are reset and measured
temperature is displayed.

How to operate total operation hours display

・

reset

Run

Stop

Mode

Set

▼

▲

Def

h.m

℃

Alarm

Heating

Auto stop

Auto start

1Step

Defrost

24Hour

Pro.

○
○
○

○

SnS

●

Press 6 times

Run

Stop

Mode

Set

▼

▲

Def

h.m

℃

Alarm

Heating

Auto stop

Auto start

1Step

Defrost

24Hour

Pro.

○

○
○

○

Addt

●

Run

Stop

Mode

Set

▼

▲

Def

h.m

℃

Alarm

Heating

Auto stop

Auto start

1Step

Defrost

24Hour

Pro.

○
○
○

○

1500

●

Run

Stop

Mode

Set

▼

▲

Def

h.m

℃

Alarm

Heating

Auto stop

Auto start

1Step

Defrost

24Hour

Pro.

○
○
○

○

cLr

●

Press 5 times

Run

Stop

Mode

Set

▼

▲

Def

h.m

℃

Alarm

Heating

Auto stop

Auto start

1Step

Defrost

24Hour

Pro.

○
○
○

○

23.5

●

Содержание LTI- 400E































































Результаты поиска

Содержание LTI- 400E

Отзывы:

Похожие инструкции для LTI- 400E

Бренды по названию

Популярные бренды

EYELA LTI- 400E, Инструкция по эксплуатации

Результаты поиска

Содержание LTI- 400E

Отзывы:

Похожие инструкции для LTI- 400E

Бренды по названию

Популярные бренды