EYELA LTI- 400E Скачать руководство пользователя страница 20

Страница: 20 / 62

-17-

Reasons why alarm is activated.

Alarm display and operations

Alarm name

Over load

alarm for

refrigeration

unit

Operating conditions
Refrigeration unit performs over load operation (or

started up).

Releasing alarm

・

Please refer to "Troubleshooting" on page 49.

・

Control will be continued.

・

Buzzer beeps for 15 seconds.

・

Alarm display

Watch dog

・

Resets microcomputer and tries to

restart control. In case that
microcomputer does not get back to
normal operation, control gets
stopped.

・

Alarm display (Not specified).

Operating conditions

Due to noise and etc, temperature controller

is in abnormal condition. Ambient temperature

exceeds 35

℃

Releasing alarm

Change the ambience and power source.

Over heat

alarm

・

Stops control of heater.

（

Recovers automatically when

sorting out the trouble).

・

Alarm display

Over Heat

※

Over heat alarm lamp lights up.

Indicator displays measured temperature,

however, other alarm may be activated.

Operating conditions

・

Setting temperature of over heat protector is

low.

・

Temperature controller, SSR or the fan in

the air jacket is impaired, which raises the
setting temperature of over heat protector.

・

Temperature exceeds the settable range of

over heat protector, which made over heat
protecting thermostat work.

（

temperature

reaches around 70

℃

）

Over cool

alarm

・

Refrigeration unit will not be controlled.

（

Recovers automatically when sorting

out the trouble).

・

Alarm display

Over Cool

※

Over cool alarm lamp lights up.

Indicator displays measured

temperature,
however, other alarm may be activated.

Operating conditions

・

Setting temperature of over heat protector is

high.

・

Temperature controller, SSR or the fan in

the air jacket is impaired, which lowers the
setting temperature of over cool protector.

Warning function

Reasons why alarm is activated.

Warning display and operations

Warning

Warning for

elapsing total

operation hours

Operating condition

・

Total operation hours exceed the setting time.

Releasing warning

・

Pressing [Set] key can release the warning.

・

Reset total operation hours

「

Addt

」

adjustment mode.

※

If you've released the warning by [Set] key

and restart control without resetting total

operation hours, warning will be reactivated

(when turning on and off the unit.)

・

The unit will be controlled.

・

Warning display

↑↓交互表示

Alarm

Heating

℃

h.m

Defrost

Addt

●
○
○

○

●

Alarm

Heating

℃

h.m

Defrost

●

19.5

○
○

○

●

Alarm

Heating

℃

h.m

Defrost

oVL

●
○
○

○

●

Alarm

Heating

℃

h.m

Defrost

●
○
○

○

●

Содержание LTI- 400E































































Результаты поиска

Содержание LTI- 400E

Отзывы:

EYELA LTI- 400E, Инструкция по эксплуатации, Страница: 20 / 62

Результаты поиска

Содержание LTI- 400E

Отзывы: