manualshive.com logo in svg

EYELA LTI- 400E, Инструкция по эксплуатации, Страница: 42 / 62

Поделиться
Скачать
EYELA LTI- 400E Скачать руководство пользователя страница 42

-39-

11)Press 

［▲］

or

［▼］

 key to input repeat count.

  ※

Each time you press 

［▲］

or

［▼］

key, the 

        value changes by 1. Pressing and holding

        the key can change the value by 10 times.

 

  ※

Repeat count can be set up to 99 times.

12

）

Press 

［

Set

］

 key.

   

 Displayed repeat count (blinking) is determined.

 

  

・

Indicator displays 

「

24SP

」 

      

(while the operation has not yet started

） 

  

 ・「

Temperature display lamp 

（℃）」

 lights up.

  ※

If no key operation is done for longer than a 

        minute after setting the value or displaying 

        

「

24SP

」

on the indicator, the display returns to 

        the measured temperature. If it happens while 

        setting the value, please repeat the procedure 

        from 1). 

13) Starting 24 hour cycle operation

 

a) While the unit is controlled, the operation gets 

      started when pressing 

［

Set

］

key.

 

b) While the unit is under suspension, press [Run / 

       Stop] key while selecting step operation. 24 

       hour cycle operation gets started. 

 

c) When selecting 24-hour cycle operation during 

      constant value control, press [Set] key three times 

      after selecting 24-hour cycle operation (measured 

      temperature will be displayed after displaying 

      setting temperature and time). 

      Then, the operation gets started. 

  ※

After displaying 

「

24SP

」

 or selecting 24-hour 

         cycle operation, the display returns to measured 

         temperature if no key operation is done for 

         longer than a minute. In such a case, select 24-

         hour cycle operation mode once again by [Mode] 

         key and start the operation. 

  
  ※

After starting 24-hour cycle operation, 

     temperature 

・

time setting and the progress

     of the programs (elapsing time and repeat 

     count at the setting value) can not be 

     checked. So please write down the setting.

 

※

1. Display until the temperature reaches at the 

       setting value of each step.

  ・

Indicator displays measured temperature.

  ・「

Time display lamp

（

h.m

）」

 blinks.

  ・「

Temperature display lamp 

（℃）」

 lights up.

  ・「

Heater lamp (Heating)

」

 lights up when the 

heater 

       is turned on.

  ・「

Refrigeration unit lamp (Refrigerator)

」

 lights up 

       when refrigeration unit is activated. 

11

）

 Setting repeat count

12

）

Determining repeat count

13)Starting 24-hour cycle operation

  

PV

Run

Stop

Mode

Set

▼

▲

Def

h.m

SV

℃

Alarm

Heating

Auto stop

Auto start

1Step

Defrost

24Hour 

Pro.

○
○
○

○

○

○

○

1

●

●

●

PV

Run

Stop

Mode

Set

▼

▲

Def

h.m

SV

℃

Alarm

Heating

Auto stop

Auto start

1Step

Defrost

24Hour 

Pro.

○
○
○

○

○

○

○

19

●

●

●

PV

Run

Stop

Mode

Set

▼

▲

Def

h.m

SV

℃

Alarm

Heating

Auto stop

Auto start

1Step

Defrost

24Hour 

Pro.

○
○
○

○

○

○

○

24SP

●

●

○

PV

Run

Stop

Mode

Set

▼

▲

Def

h.m

SV

℃

Alarm

Heating

Auto stop

Auto start

1Step

Defrost

24Hour 
Pro.

○
○
○

○

○

○

23.5

●

●

○

●

Содержание LTI- 400E































































Отзывы:

Нет отзывов