EYELA LTI- 400E Скачать руководство пользователя страница 19

Страница: 19 / 62

-16-

・

Buzzer beeps for 15 seconds.

・

Control will be continued.

・

Alarm display

Reasons why alarm is activated.

Alarm display and operations

Alarm name

Door alarm

Operating conditions

Control gets started when the door is not closed

completely.

Releasing alarm

・

Alarm can be released when door is closed

and control gets started.

・

Pressing

［

Set

］

key can stop the buzzer.

Alarm for malfunction
of temperature control

・

Buzzer beeps for 15 seconds.

・

Control will be continued.

・

Alarm display

Operating conditions

・

Temperature continues to rise for longer than 10

minutes even though displayed temperature is

higher than setting value

（

SSR for heater is short-

circuited).

・

Temperature does not rise for longer than 10

minutes (or heater is disconnected) even though
displayed temperature is lower than setting value.

・

Over heat protector or over heat protecting

thermostat worked.
Releasing alarm

・

When the measured temperature is out of the

capacity of the unit, control gets restarted
automatically.

・

Alarm can be also released by

［

Set

］

key.

・

Sort out the trouble if over heat protector or over

heat protecting thermostat works.

↑↓

Displays alternately

・

By following the setting for power

failure alarm, the unit will be

controlled or gets stopped.

・

Display of continuing control

・

Display of stopping control

Power failure

alarm

Operating conditions

Alarm is activated when power failure occurs

(or turning off the unit without stopping

control).

Releasing alarm

Pressing

［

Set

］

key can release the alarm.

※

Setting after power recovery can be

changed.

（

Please refer to the section "How to set

power recovery setting" on page 44.

・

Buzzer beeps for 15 seconds.

・

Control will be continued.

・

Alarm display

Operating conditions

Temperature sensor in the chamber is

disconnected.

Releasing alarm

Stop operation.

Sensor is required to be replaced.

Sensor alarm

Alarm

Heating

℃

h.m

Defrost

door

●
○

○

●

Alarm

Heating

℃

h.m

Defrost

cont

●
○

○

●

Alarm

Heating

℃

h.m

Defrost

PoFF

●
○
○

○

●

Alarm

Heating

℃

h.m

Defrost

●

19.5

○
○

○

●

↑↓

Displays alternately

Alarm

Heating

℃

h.m

Defrost

PoFF

●
○

○

●

Alarm

Heating

℃

h.m

Defrost

●

19.5

○
○

○

●

Alarm

Heating

℃

h.m

Defrost

SEnS

●
○

○

●

↑↓

Displays alternately

Alarm

Heating

℃

h.m

Defrost

●

19.5

○
○

○

●

Содержание LTI- 400E































































Результаты поиска

Содержание LTI- 400E

Отзывы:

Похожие инструкции для LTI- 400E

Бренды по названию

Популярные бренды

EYELA LTI- 400E, Инструкция по эксплуатации

Результаты поиска

Содержание LTI- 400E

Отзывы:

Похожие инструкции для LTI- 400E

Бренды по названию

Популярные бренды