background image

-46-

You can set the time for total operation hours display.

In total operation hours display, [Alarm] lamp 

   lights up when setting time elapses and indicator 

   displays [Addt] and measured temperature 

   alternately, and the unit is under control.

Setting total operation hours display

1)Press

Set

key for longer than 5 sec.

  

The mode changes to adjustment mode and 

     indicator displays [SnS] . Then, the mode changes 

     to calibrating displayed temperature mode.

2)Press 

[▲]

Key 5 times to enter into total operation

     hours display mode [Addtt].

3)Press

Set

key.

  

Indicator changes to display total operation hours  

     (blinking).

  ・「

Set key lamp

SV

)」

lights up.

  ※

Total operation hours display (blinking) is the 

         value that was used last time. Factory default 

         value is 

1500 hrs.

62.5days

)」

.

  4)Press 

[▲]

or

[▼]

key to set total operation hours

     display.

  ※

Each time you press

[▲]

or

[▼]

key, time 

changes 

         by an hour, and pressing and holding down the 

         key changes the value continuously. 

  5)Press 

Set

key.

  

Displayed total operation hour display (blinking) is 

     determined and indicator displays [Addt] to enter 

     into the setting for total operation hour display and 

     reset.

Changed character will not be active until you press 

   

Set

key.

To change other adjustment mode, press 

[▲]

or

   

[▼]

 key to display the mode you' d like to change.

If you don't need to change the other adjustment 

    mode, press [Set] lye for longer than 5 sec. Then, 

    indicator changes to display [Measured temperature].

If no key operation is done for longer than a minute 

    while setting, the display returns to measured 

    temperature. In such a case, please reset the setting 

    from 1).

1)Press [Set]key for longer than
 5 sec. to enter into adjustment mode.

2)Setting mode for total 
operation hours display

3)Setting total operation hours 
display

4)Setting total operation 
hours display

5)Moves to total operation hours display and 
reset mode.

6. How to set total operation hours display

PV

Run

Stop

Mode

Set

Def

h.m

SV

Alarm

Heating

Auto stop

Auto start

1Step

Defrost

24Hour 

Pro.


SnS

Press 5 times

PV

Run

Stop

Mode

Set

Def

h.m

SV

Alarm

Heating

Auto stop

Auto start

1Step

Defrost

24Hour 

Pro.


Adtt

PV

Run

Stop

Mode

Set

Def

h.m

SV

Alarm

Heating

Auto stop

Auto start

1Step

Defrost

24Hour 

Pro.



1500

PV

Run

Stop

Mode

Set

Def

h.m

SV

Alarm

Heating

Auto stop

Auto start

1Step

Defrost

24Hour 

Pro.



1500

PV

Run

Stop

Mode

Set

Def

h.m

SV

Alarm

Heating

Auto stop

Auto start

1Step

Defrost

24Hour 
Pro.



Addt

Содержание LTI- 400E































































Отзывы: