EYELA LTI- 400E Скачать руководство пользователя

Страница: 17 / 62

5. Buzzer setting

Buzzer can be beeped when the unit is stopped

automatically in auto stop mode.

※

Selectable items

oFF : NO buzzer

on : Buzzer beeps

※

Factory default

：

oFF

6. Time setting for displaying total operation hours

If you set the time setting for total operation
hours function,

「

Alarm

」

lamp will light up when

the time elapses setting time. Indicator displays

「

Addt

」

and measured temperature alternately

and the unit will be controlled.

※

Setting range of displaying total operation

hours

：

〜

9999hrs.

Factory default

：

1500 hrs.

※

Useful to check the timing of executing

defrosting (forced manual defrosting) or

maintenance and checkup.

7. Resetting total operation hours

If you reset the time, you can check the next

timing of defrosting (forced manual defrosting),

maintenance and checkup after resetting the time.

※

Factory default

：

0hr.

The setting of adjustment mode can be changed even

when the unit is controlled or not controlled.

1) Press

［

Set

］

key for longer than 5 seconds.

Indicator displays

「

SnS

」

and the mode enters

into adjustment mode.

2) Each time you press

［▲］

［▼］

key, setting

mode

changes. Choose your desired mode.

※

Adjustment mode changes in order as shown in

right picture.

For more details about operation, please refer to "How

to operate adjustment mode" on page 41.

［▼］

［▲］「

SnS

」：

Calibrating displayed

temperature

↓ ↑ ［▼］

［▲］「

AL-H

」：

Upper temperature limit

alarm

↓ ↑ ［▼］

［▲］「

AL-L

」：

Lower temperature limit

alarm

↓ ↑ ［▼］

［▲］「

PoFF

」：

Power recovery

setting

↓ ↑ ［▼］

［▲］「

buSE

」：

Buzzer setting

↓ ↑ ［▼］

［▲］「

Ａｄtt

」：

Displaying total operation

hour setting

↓ ↑ ［▼］

［▲］

「

Ａｄｄｔ

」：

Displaying total

operation hours

・

reset

-14-

※

If you set the buzzer setting, buzzer will keep on

beeping when auto stop control will be

completed (when stopping control).

Pressing [Set] key can stop the buzzer.

Содержание LTI- 400E































































Результаты поиска

Содержание LTI- 400E

Отзывы:

Похожие инструкции для LTI- 400E

Бренды по названию

Популярные бренды

EYELA LTI- 400E, Инструкция по эксплуатации

Результаты поиска

Содержание LTI- 400E

Отзывы:

Похожие инструкции для LTI- 400E

Бренды по названию

Популярные бренды