background image

- 18 -

20cm

20cm

20cm

20cm

4-1  Installation environment

Warning

Do not install in a potentially 
hazardous  location.

Since this unit is equipped with heater, it may 
cause a fire if you install it in a potentially 
hazardous location. 

Caution

Use extreme caution when selecting 
installation site, where can be 
ventilated

Since this unit is equipped with an air cooled 
type refrigeration unit, it exhausts the heat. 
Install the unit in a well-ventilated or an air-
conditioned location where the ambient 
temperature does not rise high by exhausted 
heat. The operating efficiency and the cooling 
power is worsened if the environmental 
temperature is raised. Also, refrigerator may be 
impaired because of overload and high pressure 
operation.

Select the installation site that meets the 
following conditions;

No direct sun light

Ambient temperature should be from 5 to 30

.

Well-ventilated or a location where can be 

ventilated well.

No combustible solid, liquid or gas around the 

unit.

No dew condensation

Lesser humidity and no dripping falls over the unit.

Lesser dust

Even and stable

Check the weight of the product before running

4-2 Environmental conditions

KCL-2000W   153kg

Keep good ventilation space.

The minimum space is required as shown on 
the right figure to maintain excellent 
performance of the unit.

Caution

Caution

Since the unit is a heavy product, 
use caution when carrying it.

4

Содержание KCL-2000W



















































Отзывы:

Похожие инструкции для KCL-2000W