EYELA KCL-2000W Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 50

background image

- 15 -

Alarm message is indicated with flashing at

part of LDC panel .

When several alarms occur simultaneously, 4
alarms can be indicated

with in order of

precedence.

3-5 Safety and alarm function

Safety function

Alarm function

Temp 19.5

Total Time 003/09:28

19.5

℃

Alarm indication in Normal mode

Humi 80.0

80.0

％

RH

Temp 23.5

Total Time 003/09:28

23.5

℃

Humi 70.0

70.0

％

RH

Pro  3
Seg  4
Repeat     2        001/10:18

SET

MEAS

SET

MEAS

This unit has safety and alarm functions
as below.

When you face the trouble, please refer to
[Troubleshooting] on P.35 and follow the
instructions.

Safety device

Function

Cause

Over heat protector
for temperature
inside the chamber

Turns off to shut down the power.

Electric leakage or excess current occurs.

When the temperature inside the
chamber exceeds the setting
temperature for over heat protector,
the alarm message[TH] is
displayed with flashing and all
control operations are stopped.

Mains switch

- The setting temperature for over heat protector is

too low.

-Due to some trouble of temperature controller,

SSR or chamber fan, the temperature inside the
chamber exceeds the alarm temperature

Boil-dry protector
for humidification
tray

When the top and bottom
humidification tray are empty, the
alarm message [TH1] (for top) and
[TH2] (for bottom) are indicated with
flashing and all control operations are
stopped.

- The humidification tray is not supplied water.
- Low water level of the tray.
-Due to some trouble of temperature controller or

SSR, temperature inside the chamber exceeds
the alarm temperature

Overload relay
holding circuit for
refrigeration unit

When the refrigeration unit works
under overload (overheat) or start-up,
the alarm message [OLR] is
indicated with flashing and all control
operations are stopped.

-The refrigeration unit works or starts up under

overload (overheat) .

-Due to overheat operation exceeding the cooling

capacity, temperature inside the chamber rises
abnormally.

- The environmental temperature exceeds 35

℃

.

- Low voltage

High pressure
switch for
refrigeration unit

When the refrigeration unit works
under high pressure and the
pressure value exceeds its upper
limit, the alarm message [HP] is
indicated with flushing and all control
operations are stopped.

- The refrigeration unit works under

overload (overheat).

-Due to overheat operation exceeding the cooling

capacity, the temperature inside the chamber rises
abnormally

- The environmental temperature exceeds 35

℃

.

- The fan motor for condenser breaks down.

Alarm indication in Program mode

Some alarm functions continue to control or
stop the control operation depending on its
significance of the cause.
The unit is incorporated the watch-dog system
which detects crash of CPU and resets the
circuit by self-diagnosis.

«
...
17
18
19
20
21
...
»

Содержание KCL-2000W



















































Отзывы:

Нет отзывов

Похожие инструкции для KCL-2000W

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды