EYELA KCL-2000W Скачать руководство пользователя

Страница: 21 / 50

- 17 -

Alarm name

Alarm message

Cause

Drain tank full alarm
(when you attach
an optional drain
tank.)

- Buzzer sounds for 15 seconds.
- All operations are stopped.
- The alarm message [DTK] flashes.

The drain tank (option) is filled up.

(Approx. 10L)

- Buzzer sounds for 15 seconds.
- All operations are stopped.
- The alarm message [HU2] flashes.

- Buzzer sounds for 15 seconds.
- All operations are continued.
- The alarm message [OVR] flashes.

- Buzzer sounds for 15 seconds.
- All operations are continued.
- The alarm message [OVC] flashes.

- Buzzer sounds for 15 seconds.
- All operations are continued.
- The alarm message [OFF] flashes.

- Buzzer sounds for 15 seconds.
- All operations are continued.
- The alarm message [HU1] flashes.

- Buzzer sounds for 15 seconds.
- All operations are continued.
- The alarm message [COL] flashes.

- Buzzer sounds for 15 seconds.
- All operations are continued.
- The alarm message [PRG] flashes.

* Indications disappear, and any key

operation is not accepted.

- All operations are stopped.

Humidity upper limit
alarm

Overheat alarm

Overcool alarm

Power failure alarm

Temperature
control alarm

Cooling alarm

Temperature
gradient alarm

Watch-dog

The measured humidity is left being at 100%
or 0% over 5 minutes.

After the measured temperature reaches to
the set point, it exceeds 5

℃

or higher than

the set point.

After the measured temperature reaches to
the set point, it exceeds 5

℃

or lower than

the set point.

The unit is shut down while operating.

The measured humidity deviates form the
set value

20%, and it is left for more than

60 minutes.

Although the refrigeration unit works and the
heater stops, the temperature cannot be
lowered 1

℃

under the below conditions.

-5

℃

or higher measured temp. : during 30min.

Lower than -5

℃

measured temp : during 60min.

The measured humidity deviates form the
target value

5% during the gradient control,

and it is left for more than 10 minutes.

It detects crash of CPU due to an excess
noise and stops the microprocessor.

How to release alarm.

1) In case of

Overheat protection alarm for chamber [TH]
Overload alarm for refrigeration unit [OLR]
High pressure alarm for refrigeration unit [HP]

Turn off the power switch of the unit once,
solve the cause of alarm, and turn on the
power switch again.

2) In case of

Door alarm [DOOR]

When the door is closed, the alarm is
released automatically.
* [Clear] key cannot release the alarm.

3) In case of other alarms

When you press [Clear] key, the alarm is
released.
If the cause of the alarm is not solved, the
alarm occurs again.

4) In case of watch-dog

Turn off the power switch of the unit once,
and turn on the power switch again.

Содержание KCL-2000W



















































Результаты поиска

Содержание KCL-2000W

Отзывы:

Похожие инструкции для KCL-2000W

Бренды по названию

Популярные бренды

EYELA KCL-2000W, Инструкция по эксплуатации

Результаты поиска

Содержание KCL-2000W

Отзывы:

Похожие инструкции для KCL-2000W

Бренды по названию

Популярные бренды