EYELA FDS-1000 Скачать руководство пользователя

Страница: 20 / 41

(3)Wiring

the

connector for vacuum pump

1) Disassemble

the

connector for vacuum pump

and solder

the

lead wire

of external device

on the terminal of connector.

※

Insulate soldered terminal

with heat

shrinkable tube.

※

Don't lose the

lamp and

the Screw

Assemble the

disassembled connector.

※

When attaching

the Shell

to the main unit,

turn

it opposite

※

After attaching the Shell to the Main unit, then

the Screw and the Clamp are attached.

3) Insert the plug of power cord of vacuum pump

into one of Receptacle on the right-hand side
of the main body.

vacuum pump cord

Terminal 1

：

LIVE

Terminal 3

：

EARTH

Terminal 2

：

NEUTRAL

Main

unit

Lead wire

Terminal

Heat shrinkable tube

Wiring

the

connector for vacuum pump

Soldering

※

After soldering, shrink heat shrinkable tube

with drier.

Disassembling

the

connector for vacuum pump

Main unit

Shell

Clamp for
fixing lead wire

Remove

the

crew for the

clamp for fixing
lead wire

Turn the shell
left to remove

Remove

the

crew for fixing

Shell

- 16 -

Содержание FDS-1000










































Результаты поиска

Содержание FDS-1000

Отзывы:

Похожие инструкции для FDS-1000

Бренды по названию

Популярные бренды

EYELA FDS-1000, Инструкция по эксплуатации

Результаты поиска

Содержание FDS-1000

Отзывы:

Похожие инструкции для FDS-1000

Бренды по названию

Популярные бренды