Exhausto EXact2 VEX240 series Скачать руководство пользователя страница 79

Страница: 79 / 108

HC Controller

Device

Fault code

Category

Alarm description

Troubleshooting

(See appendix 1: "Simplified diagrams" for the positioning of dampers,
sensors, air directions, etc.)

xx yy

16 01

MHCW: Module config-
ured incorrectly. Check
CN6 on circuit board.

Check the jumper in the CN6 connector on the heat control circuit
board

MHCW

: - there must be a jumper across 7 and 8.

MHCE

: - a jumper must not be fitted.

16 02

HCW: Fan speed tem-
porarily reduced

HCW

: Fan speed temporarily reduced because warning limit for

frost protection of water heating coil has been reached

16 03

HCW: VEX/CX stop
temporarily

HCW

: Fan speed temporarily reduced because stop temperature

for frost protection of water heating coil has been reached.

16 04

HCW: VEX/CX stop.

HCW

: Fan speed stopped because of frost alarm on the water

heating coil.

16 05

HCE: Run-on operating
because electric heat-
ing coil warm in last
three minutes.

HCE

: The fans run on for three minutes after the electric heating

coil has been in operation.

16 06

HC: Heat control cur-
rently run locally due to
service

: Heat control temporarily controlled by Lodam Multi Tool. Over-

ride lasts for max. 60 minutes

16 07

HC: Heat control safety
functions overridden lo-
cally due to service

: Heat control temporarily controlled by Lodam Multi Tool. Over-

ride lasts for max. 60 minutes.

16 10

HCE: Heat output re-
duced due to low air-
flow in supply air duct

HCE

: When the airflow is between 0.5 and 1.5 m/s over the electric

heating elements, full heat output is not permitted. Full heat output
is permitted only when airflow is more than 1.5 m/s over the heat-
ing elements.

16 13

HC: Heat control de-
tected which was not
selected in VEX/CX
configuration

: The heating coil is configured in menu 3.4 "Accessories".

16 14

MHC: Heat control
configured incorrectly
in connection with se-
lected VEX/CX config-
uration

Check the jumper in the CN6 connector on the heat control circuit
board

MHCW

: - there must be a jumper across 7 and 8.

MHCE

: - a jumper must not be fitted.

16 15

MHCW: No modbus
communication to wa-
ter heat control

MHCW

● Check the modbus cable between the connection board (EX-

act)/main board (EXact2) and MHCW.

● Check modbus cable for faults from HCW to the other units.

16 16

MHCE: No modbus
communication to elec-
trical heating control

MHCE

● Check the modbus cable between the connection board (EX-

act)/main board (EXact2) and MHCE.

● Check modbus cable for faults from HCE to the other units

3005167-2022-02-02

Alarms

79/108

Содержание EXact2 VEX240 series













































































































Результаты поиска

Содержание EXact2 VEX240 series

Отзывы:

Похожие инструкции для EXact2 VEX240 series

Бренды по названию

Популярные бренды

Exhausto EXact2 VEX240 series, Основные инструкции

Результаты поиска

Содержание EXact2 VEX240 series

Отзывы:

Похожие инструкции для EXact2 VEX240 series

Бренды по названию

Популярные бренды