Evoqua WALLACE & TIERNAN SFC Скачать руководство пользователя страница 217 | Manualshive

Страница: 217 / 288

background image

SFC

Operation

6.

217

Error

The following table shows and explains possible errors which can
occur. If you are unable to remedy the error yourself, please
contact your contractual partner.

Error

Cause

Remedy

No indication on
device

No power supply

External switch or fuse on

Device fuse defective

Check the power supply and replace
fuse
(Electrician)

Housing cover is fitted incorrectly

Check and, if necessary, fit the
housing cover correctly (cable possibly
trapped)

Displayed/output
value incorrect

Change on sensor or in the
sample water

Calibrating

Low controller quality
(controller swings,
setpoint not reached)

Incorrect control parameters

Check, adjust controller parameters;
perform automatic adaption on single
feedback closed-loop control

Dosing chemical tank empty

Fill, replace

Incorrect actuator selected

Check, correct actuator

Positioner or pump defective

Check, replace positioner/pump

Measured value
display not available,
although the
appropriate
measuring module is
installed

Measuring module defective or
fitted incorrectly

Check, replace measuring module
(Electrician)

Positioner/pump does
not work

Positioner in manual mode

Engage manual knob

Dosing device selected incorrectly

Select correct dosing device

Positioner/pump incorrectly
connected

Connect the positioner/pump correctly
(Electrician)

Relay defective

Check, (Electrician)

Incorrect application

Check (refer to 4.9 “Adaption” or 9.
“Wiring Diagrams”)

Positioner runs in
wrong direction

Positioner incorrectly connected

Correct connections

(Electrician)

Positioner closes

Positioner feedback interrupted

Correct connections

(Electrician)

Digital outputs without
function

Digital inputs not activated

Activate digital inputs

«
...
215
216
217
218
219
...
»

Содержание WALLACE & TIERNAN SFC

































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WALLACE & TIERNAN SFC

Бренд: Eaton Страницы: 6

Бренд: Camozzi Страницы: 33

Бренд: Camozzi Страницы: 2

Бренд: Camozzi Страницы: 64

Бренд: Talgil Страницы: 14

Бренд: Tadao Страницы: 2

Бренд: Waterway Страницы: 8

Extinguishing Control Panel BC06-2EXT

Бренд: LST Страницы: 4

Бренд: LOGICDATA Страницы: 23

Бренд: THOMSON Страницы: 81

Бренд: Gioteck Страницы: 16

TRILOGY T500 Series

Бренд: Eclipse Страницы: 20

MotorController WCC 310 UL

Бренд: Window Master Страницы: 39

Бренд: Weidmüller Страницы: 24

Бренд: M-system Страницы: 10

Бренд: M-system Страницы: 10

Бренд: M-system Страницы: 5

Бренд: Triax Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды