Evoqua WALLACE & TIERNAN SFC Скачать руководство пользователя страница 136 | Manualshive

Страница: 136 / 288

background image

136

WT.050.590.000.DE.IM.0719

Installation

SFC

5.

A Membrane sensor: FC1/FC2, CD7, OZ7, TC1/TC3
B Redox
C Conductivity
D pH
E 3-electrode sensor (single rod glass electrode)

1

Remove the protection caps from the sensors.

2

Install sensors (see figure above) in the cell body cover.

The sensors are marked as follows:

FC1/FC2, CD7, OZ7, TC1/TC3

Membrane sensor for free chlorine, chlorine dioxide, ozone and

total chlorine (A) (only possible with non-pressurized version)

Please note

Keep the dust protection caps and watering caps of the sensors for
subsequent use.

Please note

Cable extension:
The sensor cable for chlorine, conductivity and total chlorine may
be extended to a max. of 50 m.
If the pH, Redox or fluoride sensor cables must be extended (max.
50 m), an impedance converter must be attached to the sensor.
The impedance converter converts the very high-resistance
sensor signal into a low-resistance signal. Power is supplied to the
impedance converter by an installed battery. The life of the battery
is approx. 5 years; the impedance converter should be sent to us
for battery replacement.

Picture 5

DEPOLOX

®

Pool

Non-pressurized
version

Picture 6

DEPOLOX

®

Pool

Pressurized version

A

D

C

B

E

D

C

B

E

mV:

Sensor for Redox, marked "mV" (B)

pH:

Sensor for the pH value, marked "pH" (D)

µS:

Sensor for conductivity, marked "LF325" (C)

Des:

Sensor for free chlorine „DES“ (E)

«
...
134
135
136
137
138
...
»

Содержание WALLACE & TIERNAN SFC

































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WALLACE & TIERNAN SFC

Бренд: EA Страницы: 24

MusicCAST MCX-CA15

Бренд: Yamaha Страницы: 176

Бренд: PUTCO Страницы: 2

Бренд: Geberit Страницы: 12

multicomp F144-MS-1V1C1TI6RO-3

Бренд: KBR Страницы: 68

Бренд: Heat Controller Страницы: 10

Бренд: Brooks Страницы: 68

Бренд: ModelCraft Страницы: 4

Бренд: Lintec Страницы: 2

Interface Module XC

Бренд: Baer Страницы: 12

Бренд: RADIKAL TECHNOLOGIES Страницы: 36

WALLACE & TIERNAN MULTI-FUNCTIONS-CONTROLLER

Бренд: Evoqua Страницы: 4

Hauser COMPAX-M Series

Бренд: Parker Страницы: 84

Guardian 2D/3D Stabilizer

Бренд: Eagle Tree Systems Страницы: 13

Бренд: Danfoss Страницы: 44

Бренд: ICP DAS USA Страницы: 9

OMNIGRID Connect

Бренд: Kamstrup Страницы: 33

Бренд: PacComm Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды