Evoqua WALLACE & TIERNAN SFC Скачать руководство пользователя страница 164

Страница: 164 / 288

164

WT.050.590.000.DE.IM.0719

Operation

SFC

Operation

You have the following options starting from the basic display (the
basic display is opened by pressing the „ESC“ key in the menu four
times):

Switch between the
basic displays and trend
graphs

• Press the up or down key

Select menu

• Press the "MENU" softkey to

select the menu

• Press the "CAL" softkey to

calibrate

• Press the "MODE" softkey to set

the operating mode

Select a menu item in
the menu display

• Select the menu item with the

arrow keys (arrow in front of
menu item)

• Confirm the selection with

“ENTER"

Change/enter displayed
parameters

• Select the parameter with the

arrow keys (arrow in front of
parameter)

• Confirm the selection with

"ENTER"

• Change or enter the input values

using the arrow keys

• Save the input with "ENTER"

Cancel entry

• Press the "ESC" key to exit the

menu item. Entries which have
not been confirmed are reset to
their original settings.

Reactivate password
protection

This function is only active when a
password has been programmed.

• Change/enter displayed

parameters

• Block the system entry with the

"LOCK" softkey in the menu
display

Exit the menu item

• Press the "ESC" key

• Press the "BACK" softkey

Содержание WALLACE & TIERNAN SFC

































































































































































































































































































Результаты поиска

Содержание WALLACE & TIERNAN SFC

Отзывы:

Похожие инструкции для WALLACE & TIERNAN SFC

Бренды по названию

Популярные бренды

Evoqua WALLACE & TIERNAN SFC, Оригинальное руководство пользователя

Результаты поиска

Содержание WALLACE & TIERNAN SFC

Отзывы:

Похожие инструкции для WALLACE & TIERNAN SFC

Бренды по названию

Популярные бренды