Evoqua WALLACE & TIERNAN SFC Скачать руководство пользователя страница 148 | Manualshive

Страница: 148 / 288

background image

148

WT.050.590.000.DE.IM.0719

Installation

SFC

5.

5.3.6

Connect the device to the power supply

Warning!

Only authorized and qualified electricians are permitted to install
the device and open the housing. The unit may only be put into
operation when the housing is closed, and must be connected to
protection earth. Modifications to the device which go beyond
those described in this manual are not permissible.

Warning!

The device is not equipped with a mains switch and is in operation
as soon as the supply voltage is applied. An external switch or
circuit breaker is therefore necessary.
Provide a mains fuse locally (6 A). The conductor cross section of
the mains cable must be at least 0.75 mm (AWG 18).
When connecting system components (e.g. devices, motors,
pumps) as well as when entering operating data, the system
components must be switched off in order to prevent uncontrolled
activation or any incorrect function.

Caution!

To ensure safe and correct commissioning, knowledge of the
operation, connected electrical load, measurement signals, cable
assignment and fuse protection of the connected devices and
machines and the relevant safety regulations is required.
Commissioning of the device may therefore only be performed by
qualified and authorized electricians. Incorrectly connected
devices can be damaged, possibly irreparably, or cause faults in
other equipment when they are switched on or in operation.
Ensure that the measuring and control cables are not confused or
make contact with one another. Never connect or disconnect any
cables to which voltage is applied!

Please note

A line-side fuse (max. 16A) in the main supply line is necessary
when connecting to 230 V or 115 V.

Recommendation: Provide an on/off facility for the unit at the
installation site. 6A is recommended for the line fuse.

Observe local installation regulations!

Connect system components in accordance with the application-
relevant wiring diagrams (Chapter 9).

«
...
146
147
148
149
150
...
»

Содержание WALLACE & TIERNAN SFC

































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WALLACE & TIERNAN SFC

Бренд: K&K Страницы: 6

Бренд: BEIER-Electronic Страницы: 22

Бренд: Dantherm Страницы: 96

Бренд: Lawler Страницы: 4

Бренд: Hama Страницы: 46

Бренд: Galcon Страницы: 35

Elemec3 013-02-0095-002

Бренд: GAI-Tronics Страницы: 12

Бренд: Hanna Instruments Страницы: 88

Бренд: Veeder-Root Страницы: 27

Бренд: Valve Concepts Страницы: 18

Бренд: K&K Страницы: 6

Бренд: Lamtec Страницы: 22

Бренд: Lawler Страницы: 4

Бренд: QTP Страницы: 2

M16/RM N.C. DN 65 EEX

Бренд: Madas Страницы: 44

Бренд: Paradox Страницы: 2

Бренд: U-Prox Страницы: 3

Бренд: Keba Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды